MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena Are you new to knife making? Here is all the help you will need.

Reply
 
Thread Tools Display Modes
  #16  
Old 12-08-2002, 09:59 AM
tmickley's Avatar
tmickley tmickley is offline
Registered
 
Join Date: Jun 2002
Location: North Mankato, MN
Posts: 0
Alain:
I started using 3/16 pins on bolsters because I didn't know any better and it seemed to work. I picked that size for asthetics more than anything. My bolster pins showed on my earlier knives. Then I learned that they probably shouldn't. No rule against them showing, just most try to make them not show.
2ea 3/32 pins should work fine. If your pins bend when you pein or smash them, step up to 1/8.
One thing that is helpful is to not have several different size holes to drill for pins. It's a pain to switch drill bits and keep everything straight when you are doing several at once.
Reply With Quote
  #17  
Old 06-13-2015, 10:25 AM
stoney327 stoney327 is offline
 
Join Date: Mar 2014
Location: pennsylvania
Posts: 8
Mosaic pin material list

Quote:
Originally Posted by DC KNIVES View Post
I make my own.Just went to the local Ace hardware and got a decent selection of materials. A little trick to use on mosaic's as well as all pins is to rough up the exterior with sandpaper, files or a Dremel to give the epoxy something to bite on.Good luck,Dave
Hi
Though I've been a member for a short while. I'm new to posting and I hope this is the correct way and place to do this?
I have been in the knife game since 1966, but have just started using Mosaic pins?
That being said, is there any list of what sizes of materials ( rods, squares, tubes, etc., etc.) that I could use to produce my own 3/16" Mosaic pins? I don't really want to spend $50.00 and 2 hours of my time at Ace Tru Value, trying every combination of miscellaneous material that might fill the inside of a 3/16" Stainless steel tube? Is there anyone here who has an actual list of material that will make a decent 3/16" Mosaic pin? I'm not looking for a comprehensive item list, just a plain, down and dirty 3/16" pin? Thank you very much for any help you can give.
Kindest regards:
Stoney 327
Reply With Quote
  #18  
Old 06-13-2015, 10:41 AM
Ray Rogers's Avatar
Ray Rogers Ray Rogers is offline
Founding Member / Moderator
 
Join Date: Jun 2002
Location: Wauconda, WA
Posts: 9,840
I doubt you'll find any such list and if you do find one it will only be partly useful. The reason for that is that the patterns in mosaic pins are usually made up of tight fitting parts. You can't count on those pins and tubes being precisely their nominal size. So, if I tell you I bought a 3/16 square tube and put several 3/64 pins in it around a 1/8 pin you might go buy parts that were sized that way and find they won't fit because some one or even all of them are a thou larger than nominal. I know when I actually did build some of those pins fitting the pieces together required a fair amount of sanding to reduce the little brass rods or other parts so that everything would go together.

I did it, it was interesting but every place that sells knife supplies now carries a huge variety of mosaic pins made by people who dream up patterns I would never imagine. It is considerably cheaper and much less time consuming to just buy the pins. I'd rather spend my time making the knife than the pins especially when I know I'll probably have a better pin that way ....


__________________

Your question may already have been answered - try the Search button first!






Reply With Quote
  #19  
Old 06-13-2015, 05:11 PM
stoney327 stoney327 is offline
 
Join Date: Mar 2014
Location: pennsylvania
Posts: 8
Mosaic pin response

Quote:
Originally Posted by Ray Rogers View Post
I doubt you'll find any such list and if you do find one it will only be partly useful. The reason for that is that the patterns in mosaic pins are usually made up of tight fitting parts. You can't count on those pins and tubes being precisely their nominal size. So, if I tell you I bought a 3/16 square tube and put several 3/64 pins in it around a 1/8 pin you might go buy parts that were sized that way and find they won't fit because some one or even all of them are a thou larger than nominal. I know when I actually did build some of those pins fitting the pieces together required a fair amount of sanding to reduce the little brass rods or other parts so that everything would go together.

I did it, it was interesting but every place that sells knife supplies now carries a huge variety of mosaic pins made by people who dream up patterns I would never imagine. It is considerably cheaper and much less time consuming to just buy the pins. I'd rather spend my time making the knife than the pins especially when I know I'll probably have a better pin that way ....

Thank you Ray That sounds like very good advice. I'm a machinist by trade and am painfully aware of the discrepancies in the specs on stock material? These Industry acceptable tolerances, may be great for some metal butchers , but they're a killer when you're trying to be precise !
Stoney
Reply With Quote
Reply

Tags
bee, blade, brass, build, epoxy, files, fixed blade, hardware, hunting knife, knife, knives, made, make, making, material, materials, mosaic, pins, stainless, stainless steel, steel, supplies


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 07:08 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved