MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > The Display Case

The Display Case A place to post your latest knives and creations. Let the Knife Network community see your work first!

Reply
 
Thread Tools Display Modes
  #1  
Old 09-15-2004, 11:07 PM
Jason Cutter Jason Cutter is offline
Living Legend
 
Join Date: Sep 2002
Location: Melbourne, Australia
Posts: 1,903
First Fillet Knife.

This one was a challenge. Again a request from a friend who wants a real using knife. Just a basic Scotchbrited finish on the blade. Not my favourite idea of the best handle colour etc, but it was the customer's request. I left a bit of grinding till after HT to reduce the warpage problem, but the blade just kept moving from side to side, while grinding, even after HT ! The handle is quite thin, but comfortable and will allow use with heavy gloves on. Because it is slab-sided, it is easy to index in the hand. The shape is based on my Lightfighter bowie knife.

Anyway, feedback appreciated. This is my first successfully executed fillet knife. Thanks. Jason.




__________________
JASON CUTTER BLADEART
Jason Cutter @ Dr Kwong Yeang
Knifemaker, Australia
(Matthew 10.16)
Reply With Quote
  #2  
Old 09-16-2004, 04:54 AM
Phantom23 Phantom23 is offline
Steel Addict
 
Join Date: Oct 2003
Location: Burpengary, Queensland, Australia
Posts: 149
Jason,
I have just finished the blade on my first fillet knife, it's out of 1.6mm 440c and 4.5' blade. I have about 5 knives in the shed and hope to do another fillet and cooks knife next week when I am off work and send them to Hills by next friday.

Is it sub- tang constuction? if so how /which pins keep the blade in.

My handle is based on my hunter knife lol lol

It looks like it will do the job. My only comment would be old mate must catch bigger fish than me. The whiting and bream I get onto will be covered by the 4.5 inch blade. I made it that size because I don't like the longer blades I have.

I found not much room for error with the thin steel on my equipment (read slightly modified blade design)

Phantom 23
Reply With Quote
  #3  
Old 09-16-2004, 09:29 AM
luc luc is offline
Skilled
 
Join Date: Jul 2003
Location: Albuquerque, NM
Posts: 345
Jason!
Your a madman, That is by far the coolest fillet knife I have ever seen!
I love it!
Lucas


__________________
Lucas Burnley
Stop by and check out my site!
http://burnleyknives.blademakers.com/
Reply With Quote
  #4  
Old 09-16-2004, 09:22 PM
gary wendell's Avatar
gary wendell gary wendell is offline
Enthusiast
 
Join Date: Jun 2004
Location: charleston,wv
Posts: 82
Jason, one of the best designed and practical fillet knives I've seen..........Gary
Reply With Quote
  #5  
Old 09-19-2004, 01:35 PM
paul savage paul savage is offline
Steel Addict
 
Join Date: Jul 2004
Location: Ayr Ont. Canada
Posts: 144
filet knife

Jason, good looking knife. Filet knives are one of my favorites and living in Canada mine get their share of use on every thing from perch(not very big) to salmon(pretty big15-30 lbs). Great use of colour & materials.It's nice to think outside the box.I use 440c as well but I just profile & drill my holes prior to heat treat , leaving the blade grinding till after. It is a little harder on belts but I seem to end up with better results.Using 440c at work (industrial knife shop) I've come to learn that if you take equal amounts of material off it always comes back to straight . Anyways , enough idle chatter.Again, great looking knife. Paul
Reply With Quote
  #6  
Old 09-19-2004, 02:23 PM
Jason Cutter Jason Cutter is offline
Living Legend
 
Join Date: Sep 2002
Location: Melbourne, Australia
Posts: 1,903
Phantom - I was trying out a different pin method. The 2 first pins on the top and the first pin at the guard side of the handle sit in notches in the tang. This way, I don't have to have more pins in the centreline of the handle. I personally like pins along the perimeter of the handle - I think its actually stronger.

Its also a good way to "salvage" a blade thats been heat treated, if you forget to drill the holes beforehand. The notches in the tang can simply be cut in with a Dremel tool using the reinforced cuttoff wheel to fit the position of the pins.

Paul - as it turns out, through trial and error (and a lot of swearing...) I'm now doing what you've described. I only profiled and cut the edge bevels in before HT.

Thanks to all for the feedback. Jason.


__________________
JASON CUTTER BLADEART
Jason Cutter @ Dr Kwong Yeang
Knifemaker, Australia
(Matthew 10.16)
Reply With Quote
Reply

Tags
blade, fishing knife, forge, knife, knives


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 02:09 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved