Custom Knives | Other Knives | General Items
New Posts | New PhotosAll Photos

Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Tool Time

Tool Time Let's talk shop. Equipment, Tips & Tricks, Safety issues - Post it here.

Thread Tools Display Modes
Old 05-24-2021, 04:45 PM
KenH KenH is offline
Join Date: Dec 2012
Location: South Baldwin Co across the bay from Mobile, AL
Posts: 85
SG Repair

Hello folks. Many of us have built the SGA. The SGA is so handy, it's one of my much used tools in the shop.

A few days ago I was sanding a Damascus Billet and got it down around 1/4" thick and starting to look pretty good. I decided to check to make sure the magnetic chuck was still even, so removed billet, adjusted chuck so it was just "kissing" the chuck face. Looked good. I went to do something else and an hour later when I came back I stuck the billet back on and moved to sand - WHAM!!!!! I'd forgot to move chuck back to provide clearance for the 1/4" billet. With the SGA running at WAO at 4,050 SFPM it really shot that chuck thru, billet went flying and something is broke in the adjustment portion.

OK, no big deal, I built the darn thing I can fix it. I take adjustment portion apart, find the problem and fix it. Great, now ready to go again. Wrong - there is big time slop in the chuck now. Take a look at photo below:

You see the round rods on inside of the rails? That is where the rollers run with no slack (heck, we know how it works). After the WHAM! something happened to cause too much slack and gave wobble in the chuck. I couldn't see anything wrong - it all looked good. I took a roller off the slide and found what happened. See the brass circle on the slide (left side)? The screw that holds the roller screws into that, and if you look close you can see the screw hole is offset from center a small amount. This gives the ability to rotate the brass circle and remove all slack. See the two small holes on the edges of brass circle? That's got a sharp pointed setscrew so the brass can't move in use. I "think" it's going to work now. It feels good, no slop - and is a tad tighter than when new but I think I'll leave it there for now.

Shows what can happen with a moment of "not thinking" - which seems to happen more often the older I get.
Reply With Quote

back, bearing, billet, brass, damascus, make, photo, problem, repair, sanding, screw, screws, sharp, shop, small, tools, wobble

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Old Western repair Rancid Crabtree This Old Knife 4 07-14-2008 12:43 AM
anvil repair Gus B Able Ed Caffrey's Workshop 2 01-06-2008 04:57 PM
Repair flaviopknife Fit & Finish 1 08-17-2007 07:02 AM
Anvil repair bbarnettAUS Ed Caffrey's Workshop 2 02-26-2007 10:59 PM
folder repair wookie69 The Folding Knife (& Switchblade) Forum 5 01-01-2007 08:36 PM

All times are GMT -5. The time now is 05:58 AM.

Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved