MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Ed Caffrey's Workshop

Ed Caffrey's Workshop Talk to Ed Caffrey ... The Montana Bladesmith! Tips, tricks and more from an ABS Mastersmith.

Reply
 
Thread Tools Display Modes
  #1  
Old 06-07-2014, 02:25 PM
Jeremy Jeremy is offline
Steel Addict
 
Join Date: Jun 2011
Location: Idaho
Posts: 234
First tomahawks and a hatchet

I'll start off with a disclaimer-these are a LONG ways from Ed Caffrey axes, but it's my meager first attempts . I was able to go to a friend's shop earlier in the week and he helped walk me through the various steps of forging some tomahawks. He also had a little hatchet that I really liked so I forged one similar to it out. The first here was made out of some cable Damascus I'd made a while back. The cable got thin enough that I welded together three pieces of it into a big blank which I used for a spike hawk:



After a little cleanup on the grinder:



The next is something I've wanted to do for a long time. It's a wrought iron (wagon wheel rim) wrapped hawk with a piece of high carbon steel forge welded to the back before wrapping (for a hammer pole). Then another piece put in for the bit. It was definitely the hardest of the three to do. The wrought wanted to move faster than everything else and it is certainly the ugliest in the just forged stage... I also really tried paying attention to how many hammer blows I had on each side as I cross peened the blade to keep things even. But...it ended up a bit thinner for the wrought on one side, so when I grind then etch, it won't be even on both sides for where the wrought goes to. Oh, well-I guess worse things have happened. This one will need the most work of the three on profiling. I got to a point where I didn't want to try forcing things around anymore with how the wrought was going all over.



The last is a little hatchet that I'm pretty hopeful for. It started out as a 3/4" thick block of mild steel. Drilled a few holes to help with slitting and drifting (more on that shortly...) and a 1 1/2" deep cut in the end to put a bit in later. This was a bigger piece of steel than the others, but for some reason, the cross peening went better than either of the other two and quicker. I'm going to grind in a subtle curve up to the top of the edge and probably shorten the blade just a bit, which will also help get rid of the small area on the edge where the mild started going over the carbon bit.



I learned a LOT while doing these and took one more step towards having "man hands" after all that hammering . Slitting and drifting is quite the skill-one which I don't seem to have yet. Even with holes drilled to help keep things straight, I still had difficulties. It was fairly frustrating as I'd see one side of the eye bulging out more than the other... Thankfully, my friend was there to keep giving advice on how best to proceed. Hopefully I can grind things back to even on the eyes, as we made sure the blade was at least centered with the drift. Lots of fun and looking forward to seeing how these finish out. Any advice or suggestions are very appreciated.


Jeremy
Reply With Quote
  #2  
Old 06-08-2014, 02:50 PM
Bob Hartman Bob Hartman is offline
Steel Addict
 
Join Date: Feb 2006
Location: Boise, ID
Posts: 105
Looking good Jeremy, looks like a day at Doc's got you fired up. What size cable did you start with?
Reply With Quote
  #3  
Old 06-08-2014, 04:02 PM
Jeremy Jeremy is offline
Steel Addict
 
Join Date: Jun 2011
Location: Idaho
Posts: 234
Hi, Bob . I want to say the cable was about 1", but after getting welded solidly, it ended up smaller than that. Enough that we welded 3 pieces of it together and into a square billet. I did that at Doc's place quite a while back, too.

It was a lot of fun getting to do the forging with him. Having him there to give suggestions as I tried to drift them out was really helpful. Not having done it before, I wondered a few times if it was all messed up beyond help. But, with a few tweaks and tricks, they were all salvaged. A lot of cross peening for the blades, though . I opted for that instead of the power hammer so as not to completely mess things up any faster than I already was. It was worth it and you can actually move a fair amount of material pretty quickly with a hammer. Hoping to be able to make something decent out of these.


Jeremy
Reply With Quote
Reply

Tags
advice, art, back, blade, block, carbon, damascus, edge, etch, forged, forging, grind in, grinder, hammer, iron, knife, made, make, man, material, pole, shop, steel


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
3 Tomahawks by Serapião LCASERAPIAO SBC Forum (Sociedade Brasileira de Cuteleiros) 16 07-07-2011 08:43 PM
3 Tomahawks. Luciano_Chaves SBC Forum (Sociedade Brasileira de Cuteleiros) 11 08-16-2008 08:47 AM
Tactical Tomahawks rbranan The Outpost Gallery 0 03-08-2008 06:10 PM
3 Tomahawks Don Abbott The Outpost 5 01-05-2007 03:51 PM
Tomahawks Rade L Hawkins The Display Case 2 01-24-2002 10:53 AM


All times are GMT -5. The time now is 05:28 AM.




KNIFENETWORK.COM
Copyright © 2000
CKK Industries, Inc. • All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved