MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Tool Time

Tool Time Let's talk shop. Equipment, Tips & Tricks, Safety issues - Post it here.

Reply
 
Thread Tools Display Modes
  #1  
Old 05-18-2018, 03:17 PM
rockhound's Avatar
rockhound rockhound is offline
Skilled
 
Join Date: Jun 2012
Location: Winter Park, CO
Posts: 366
Question Logo Etching Questions - Lectroetch

I am new to etching and could use a little help. I have the Lectroetch Model 6A pictured below. It has a range of 0 - 26V with a variable control knob (0 - 100). I purchased my stencils from Ernie at Blue Lightning and they look great. Ernie is a great guy, I watched his vid on how to etch and tried his steps. I'm not quite getting the results I want and am hoping I can get some advice here. I've only attempted three etches, they are all similar.
Problem: Etch is not turning black throughout.
I'm doing as Ernie said, 3 intervals of 5 seconds on about 14V DC (guessing by the dial percentage)... then repeat while switched to AC. He was using a different steel however and it was heat treated.
The steel I'm experimenting on is CPM154, not heat-treated. Not sure if hardness plays a role in this at all. It has a 400 grit finish.
Should I crank it up higher for this type of steel?
or....
Hold the pad down for longer, or more intervals during the AC phase?
Any help VERY much appreciated!

2018-05-18_01-56-45 by Chris Evenstad, on Flickr

2018-05-18_01-57-19 by Chris Evenstad, on Flickr


__________________
Stay away from fast women and slow horses
Reply With Quote
  #2  
Old 05-19-2018, 11:11 AM
rockhound's Avatar
rockhound rockhound is offline
Skilled
 
Join Date: Jun 2012
Location: Winter Park, CO
Posts: 366
Ok... I thought about this for a bit and decided fewer 5 second intervals (2) on DC. Then switched to AC and increased my pad application to more 5 second intervals (4).
Getting closer to what I want.

2018-05-19_10-06-32 by Chris Evenstad, on Flickr


__________________
Stay away from fast women and slow horses
Reply With Quote
  #3  
Old 05-20-2018, 10:24 AM
Andrew Garrett's Avatar
Andrew Garrett Andrew Garrett is offline
Moderator
 
Join Date: Jun 2005
Location: Nampa, Idaho
Posts: 3,584
Looks like you are dialing it in just fine.
Nice logo


__________________
Andy Garrett
https://www.facebook.com/GarrettKnives?ref=hl
Charter Member - Kansas Custom Knifemaker's Association
www.kansasknives.org

"Drawing your knife from its sheath and using it in the presence of others should be an event complete with oos, ahhs, and questions."
Reply With Quote
  #4  
Old 05-23-2018, 09:26 PM
M&J's Avatar
M&J M&J is offline
Master
 
Join Date: Dec 2004
Location: So. Cal
Posts: 886
Doing good! Will take some trial error to dial in. As the fluid burns off that will also change how the mark is. Every so many burns clean the stencil so that the particulates don't clog it up.


__________________
Mike
Reply With Quote
  #5  
Old 05-25-2018, 09:52 AM
rockhound's Avatar
rockhound rockhound is offline
Skilled
 
Join Date: Jun 2012
Location: Winter Park, CO
Posts: 366
Thank you! I was wondering about cleaning the stencils and glad that you mentioned it.
What product do I use to clean the stencils?


__________________
Stay away from fast women and slow horses
Reply With Quote
  #6  
Old 05-28-2018, 01:49 PM
M&J's Avatar
M&J M&J is offline
Master
 
Join Date: Dec 2004
Location: So. Cal
Posts: 886
There are a variety of cleaners provided by the stencil makers I've used in the past. A quart sized bottle is about $12-$15. Like this one from Marking Methods:
https://www.markingmethods.com/store...&idcategory=10

Lately I've begun using dish washing liquids and gently rubbing between my fingers for stencil cleaning.

Some stencils have better or worse longevity depending on size of font, the material they are made and such. I've had stencils that 10 really clean marks are about it and others that go ~40-50 with. Many variables though mostly related to how deep a cut is made and current used to obtain that. The higher the setting the more current and heat that is produced in the process.


__________________
Mike
Reply With Quote
Reply

Tags
advice, ca, chris, clean, cleaning, cpm, etching, heat, help., how to, logo, made, makers, marking, material, ore, steel, stencil, store


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Etching logo in titanium dennyg The Folding Knife (& Switchblade) Forum 7 03-05-2018 04:46 PM
Etching Name/Logo Experiments Ed Caffrey Ed Caffrey's Workshop 12 10-22-2012 08:59 AM
logo etching cedarfluteman The Newbies Arena 8 01-29-2012 06:23 AM
Saltwater logo etching... Mike Krall The Newbies Arena 2 05-31-2005 11:02 PM
Logo Etching Question Jeff Sorensen The Newbies Arena 3 01-16-2005 06:06 PM


All times are GMT -5. The time now is 04:11 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved