The Newbies Arena Are you new to knife making? Here is all the help you will need. |
03-17-2017, 08:04 PM
|
Member
|
|
Join Date: Mar 2017
Posts: 11
|
|
Optimum size wood to stabilize?
So, after many years of woodworking, I've accumulated a bit of exotic and figured wood cut-offs. I'm thinking of sending some off to get stabilized for use as knife scales.
Is there an optimum size I should mill these to prior to stabilizing? Really have no plans for certain size knives.
Is it practical to attempt stabilization on my own? From what I've read, having it professionally done makes the most sense.
Most of what I have is either surfaced 3/4 or 5/4 rough.
Thanks!
|
03-17-2017, 08:28 PM
|
|
Founding Member / Moderator
|
|
Join Date: Jun 2002
Location: Wauconda, WA
Posts: 9,840
|
|
Definitely let the pros do it. Google K&G Finishing, Lakeside,AZ and read their requirements for stabilizing. If memory serves, they can handle anything up to 2x2x24" .....
|
03-17-2017, 09:17 PM
|
Steel Addict
|
|
Join Date: Apr 2004
Location: Northern CA.
Posts: 114
|
|
I use another company for stabilization of my burl wood. They recommend nothing over 2 inches for width and height for best penetration of the stabilization compounds. I did not ask about length of the blocks as I normally cut my blocks to 5 or 5-1/2 inch.
__________________
RELH
|
03-17-2017, 09:26 PM
|
Enthusiast
|
|
Join Date: Jan 2017
Location: Saukville, WI
Posts: 74
|
|
Rickoo, sounds like those 3/4 could be cut down the middle for 1/4 to 3/8 inch thick scales, by far my favorite size, any thicker and you are doing a lot of sanding to bring them down, and like Bob said 5 inch length is perfect.
Carl
|
03-18-2017, 08:45 AM
|
|
Founding Member / Moderator
|
|
Join Date: Jun 2002
Location: Wauconda, WA
Posts: 9,840
|
|
The one thing you don't want to do is cut your scales to finished size before stabilizing. The stabilizing process will often cause a slight warp even in a normal sized handle block so it can really bend a scale sized piece. So, send handle blocks or larger when possible and make them a little bigger than you need just to be safe ...
|
03-18-2017, 11:43 AM
|
Enthusiast
|
|
Join Date: Oct 2015
Location: Eastern Kansas
Posts: 45
|
|
I hope I'm not highjacking this thread to badly but I have a question. Can anyone tell me why I shouldn't stabilize wood at home. I have been stabilizing wood for predator calls for a year or so now and I'm getting the resin all the way through a 1 1\4" x5" block. I can pull 27 in of vac so the pros won't get much more than that or is it the resin they are using?
I'm not trying to start a fight just curios that's all. I'm satisfied with the results I'm getting so I won't be changing but just curious.
Sam
|
03-18-2017, 12:22 PM
|
|
Founding Member / Moderator
|
|
Join Date: Jun 2002
Location: Wauconda, WA
Posts: 9,840
|
|
You can get decent results with some home stabilizing, sometimes even excellent results if you're set up for cactus juice. But, the pro process uses a better resin and 4000 psi of pressure in addition to the vacuum. The vacuum process can get your resin all the way through the wood if the wood is porous enough but the pressure gets the resin inside every cell of the wood. At least, that's how it was explained to me.
For most people, when you look at the time required, the mess, and the cost of doing effective home stabilizing for the amount of wood one maker can use it can be hard to justify the expense. I'd rather send my wood out and put my time and effort into making knives ....
|
03-18-2017, 12:45 PM
|
Member
|
|
Join Date: Mar 2017
Posts: 11
|
|
Just what I was looking for. Thanks everyone.
|
03-18-2017, 03:58 PM
|
Enthusiast
|
|
Join Date: Jan 2017
Location: Saukville, WI
Posts: 74
|
|
Thanks for the info about warpage Ray, I did not know that, but good to know as I have some oak from my grandpa cabin which is over a hundred years old which I plan to send out and have stabilized.
Carl
|
03-18-2017, 04:05 PM
|
Enthusiast
|
|
Join Date: Oct 2015
Location: Eastern Kansas
Posts: 45
|
|
Thanks for the info Ray. I didn't know they also used pressure that would definitely make a difference. However I seem to have more time than money and this is a hobby so I'll just keep on the way I'm doing (:
|
Tags
|
art, at home, bee, block, burl, handle, hobby, home, knife, knife scales, knives, make, making, mill, resin, sanding, scales, stabilization, stabilizing, wood |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
All times are GMT -5. The time now is 06:40 AM.
|