MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Factory Knife Customization & Mid-Tech Boards > Knife Kits Forum

Knife Kits Forum New to the art of knife making? Learn to make awesome knives, using advanced hands-on training inside. From KnifeKits.com.

 
 
Thread Tools Display Modes
  #1  
Old 10-21-2003, 11:36 AM
ToxicSteel ToxicSteel is offline
Registered
 
Join Date: Oct 2003
Posts: 2
DDR3 Scales?

Dumb noob question here, but what exactly does "pre-machined" scales mean? How much finishing is required? Thanks in advance!
  #2  
Old 10-21-2003, 12:01 PM
Jakedog Jakedog is offline
Enthusiast
 
Join Date: Nov 2002
Location: central, NC
Posts: 68
QUestion

Pre-machined scales mean that, for the most part, they are pre-cut to a rough fit of the knife handle profile. All curves and angles are cut for you but some material removal will be required to get a nice fit with the liners/bolsters.

The scales can be "finished" with as little as sand paper or a $1000 worth of fancy equipment that some people have aquired (coughdenniscough)(insert smile here).

Read over the past postings and they will give you a good idea as to what may be required, mostly that will depend on the extent you may want to embellish your work. Hope this helps

Bill


__________________
From there to here,
from here to there,
funny things are everywhere.
TG - 1960
  #3  
Old 10-21-2003, 12:54 PM
Osprey Guy's Avatar
Osprey Guy Osprey Guy is offline
Moderator
 
Join Date: Jun 2002
Location: Baltimore, MD
Posts: 2,965
If only all my new equipment did cost just a mere $1000....Thanks to my being sucked into knifemaking thanks to the kit knives (and in turn, exposed to a whole new world made up of power tools, exotic woods, and lots of steel), my workshop has gone from 0 to 180 mph in under 2 years!


One of the biggest advantages of starting off with the pre-machined scales is that the screw holes have been pre-drilled. Without access to a drill press trying to make your own scales can be a bit tricky...

May I strongly suggest you take some time every day to read through these forums. Here in the kit knife forum alone there is a wealth of info...and it's all free for the taking! There are many threads here that talk at length about finishing the scales...and the rest of the knife...which sandpaper grits, files, torx #######, respirators, various types of embellishment, the list goes on. You can get by with just a few, varied sheets of sandpaper, a paper toxic dust respirator, and some torx #######...and as you get sucked in, you can buy all sorts of goodies in support of this highly addictive narcotic we call knifemaking.


Good luck. If you have any questions, you know where to post 'em.


Dennis Greenbaum

Yeah Baby!
  #4  
Old 10-21-2003, 01:11 PM
ToxicSteel ToxicSteel is offline
Registered
 
Join Date: Oct 2003
Posts: 2
Ahhhh... nice.

My dad's a machinist so I could always make the trek up to his house to borrow the use of some of his machinery.
  #5  
Old 10-21-2003, 08:31 PM
Bob Sigmon's Avatar
Bob Sigmon Bob Sigmon is offline
Moderator
 
Join Date: Jun 2002
Location: Plymouth, MI
Posts: 1,228
Toxic,

You lucky dog, you better be sucking up to Dad real good.

Cause as you get more and more sucked into knifemaking, you're going to find out that access to lathes and mills and most important the setup knowledge to use these tools will be invaluable!

Good Luck with your projects,

Bob Sigmon
  #6  
Old 04-22-2015, 10:23 PM
TexasJack's Avatar
TexasJack TexasJack is offline
Super Moderator
 
Join Date: Apr 2004
Location: Southeast Texas
Posts: 2,919
For the most part, power tools let you do the job - or screw up the job - faster than doing it by hand.

The DDR3 only needs some basic hand work to finish it out.


__________________
God bless Texas! Now let's secede!!
  #7  
Old 03-16-2016, 03:51 PM
Neil McCauley Neil McCauley is offline
Enthusiast
 
Join Date: Sep 2015
Posts: 37
Since we're on the topic-- What pre-machined scales are available for the DDR3-BL? Is it just the Macawood ones listed on knifekits.com? Are there any in other materials elsewhere? Haven't been able to find any.
 

Tags
bee, bolsters, ddr3, hand, knife, knifekits, knifekits.com, knives, materials, profile, sand, scales, tools


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 09:03 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved