![]() |
![]() |
![]() |
|
![]() |
![]() |
||
![]() |
![]() |
|
![]() |
|
The Display Case A place to post your latest knives and creations. Let the Knife Network community see your work first! |
![]() |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Michael Fong - straight razor
Been a LOOONNNNGGG time for one of these.
Told Junko I'd be a quick 45 minutes working on a fixed blade sheath. Well, this was calling so decided to buff the handles out. One thing lead to another... I came in the door and she commented, "quick 45 minutes?!" Yup...knife time means 3X-4X what I say. ![]() ![]() __________________ Mike ![]() ![]() |
#2
|
||||
|
||||
![]() |
#3
|
||||
|
||||
Thanks Don.
![]() __________________ Mike ![]() ![]() |
#4
|
||||
|
||||
Don't thank me. THANK YOU!!
|
#5
|
||||
|
||||
Started in on some others:
![]() ![]() The bevel from the 5" leaves some to be desired, perhaps a 3" wheel would be nice. Not as thin as I'd like. These are fairly thin at the edge and I'd like to wash that up higher. __________________ Mike ![]() ![]() |
#6
|
|||
|
|||
My 1x42 has a 4" wheel after the cork I put on it.
|
#7
|
||||
|
||||
This is the thinnest production razor I have.
![]() Will look into some other wheel options. Thanks Jim! __________________ Mike ![]() ![]() |
#8
|
||||
|
||||
Completed the other one:
![]() __________________ Mike ![]() ![]() Last edited by M&J; 02-24-2019 at 07:49 PM. |
#9
|
|||
|
|||
Beautiful razors. Having only made a few, they are deceptively complicated.
|
#10
|
|||
|
|||
Beautiful work
|
#11
|
||||
|
||||
One of those pop my head out of the ground to see what is happening time. LOL. The pandemic was mentally draining and I began hibernating. This is a fit up on these. The lower one is a 1095/ni damascus from Daryl Meir. Looking forward to etching it
![]() __________________ Mike ![]() ![]() |
#12
|
||||
|
||||
Did one with some 3/32" stock for the next batch. I've also done a bit of clean-up on the 2" wheel which works well. Happy with how thin this came out.
![]() __________________ Mike ![]() ![]() |
#13
|
|||
|
|||
Nice work!
|
#14
|
|||
|
|||
At first glance I thought, "Why would he make it out of 3/16ths?" Then I read the note up above at 3/32 and went, "Oh!". LOL Not 1/16th grad.
I have Rulers the same, 1/32 and 1/64 on one side and 50ths and 100ths on the other side. A Starrett Tri Square I bought in 1978. That is some accurate grinding and a good photo. |
#15
|
||||
|
||||
Thanks. One of the parts about grinding on a smaller wheel is going through or being to thin in areas not necessary. A grinding jig would be nice if deciding to make more.
__________________ Mike ![]() ![]() |
![]() |
Tags |
1095, a, bee, bevel, blade, blades, ca, clean, damascus, edge, fixed, fixed blade, grinding, handles, hunting knife, jig, knife, made, make, photo, razor, sheath, thin |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Michael Fong- WIP fixed blade | M&J | The Display Case | 6 | 01-21-2019 06:53 PM |
Michael Fong- Memory lane knife pics | M&J | The Display Case | 0 | 12-10-2018 02:12 PM |
MY First straight razor | ironarm knives | The Damascus Forum | 7 | 04-13-2012 11:21 PM |
straight razor info | BUGSY | Knife Network Community | 4 | 08-22-2006 04:56 PM |