MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena Are you new to knife making? Here is all the help you will need.

Reply
 
Thread Tools Display Modes
  #1  
Old 04-26-2017, 04:18 PM
Hunter10139's Avatar
Hunter10139 Hunter10139 is offline
Skilled
 
Join Date: May 2012
Location: Northern Alabama
Posts: 396
Finally making a few more.....

....including one for the KITH. I thought I might do a WIP thread so here are my first 2 pics of the three knives, one after profiling and one after drilling and hardening. For those wondering, these are 1095 water quenched prior to grinding bevels.

Edit: Forgot to mention, the top one in the photos is supposed to be the KITH knife. Unfortunately it warped during the heat treatment so I'm going to try to straighten it during the temper. If it refuses to straighten I may have to start fresh.
Attached Images
File Type: jpg IMG_20170425_205025528_800x450.jpg (82.3 KB, 29 views)
File Type: jpg IMG_20170426_155741915_800x450.jpg (103.4 KB, 36 views)


__________________
-Hunter
Reply With Quote
  #2  
Old 04-27-2017, 08:57 AM
dtec1 dtec1 is offline
Guru
 
Join Date: Aug 2015
Location: putnam county NY ....about 45 mins north of new york city
Posts: 1,443
Good job they look good so far. I never quench in water. I use parks 50 90% of the time most of my knives are shorter so very rarely do I end up with a warp. But I forged a very long (for me anyway 18inch ) knife when I went to HT I got a warp in it. To get it out I knew I would have to Re HT so I was planning on normalizing then heating it in the forge and flattening it. However I realized on the first normalizing cycle it was hot enough to flatten so on the second cycle I pulled it out and straightened it with a hammer.....then did 2 normalize cycles and its dead straight now so I will try to HT again today hopefully no warp this time. If you gota get it hot enough to normalize any way wht not straighten it out right then and there
Reply With Quote
  #3  
Old 04-27-2017, 03:27 PM
Hunter10139's Avatar
Hunter10139 Hunter10139 is offline
Skilled
 
Join Date: May 2012
Location: Northern Alabama
Posts: 396
I can't really justify to the wife spending the money on parks 50 unfortunately. I also find that while water is riskier, it's also cleaner and easier to use than oil. Plus, I've had a relatively easy time straightening blades during the temper before so I'm hoping everything will be okay this time. I don't forge so most of the time I don't see any significant warping, this just must've been some sort of stress I induced in the steel while grinding it.


__________________
-Hunter
Reply With Quote
Reply

Tags
1095, bee, blades, easy, flat, forge, forged, grinding, hammer, hot, knife, knives, making, profiling, quenched, steel, temper, warping, water


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Finally get to use my new toy!!! Naboyle The Newbies Arena 6 11-01-2013 01:58 PM
Finally Getting Something Done!!!!!!!!!!!!!!!!!!!!!!! Kirby Bletcher The Display Case 13 10-06-2009 04:29 AM
Finally done... Zimba The Sheath/Holster Makers Forum 3 04-14-2008 08:51 PM
KMG is finally set up Txcwboy Tool Time 7 10-16-2007 10:28 PM
Finally. :) luc The Display Case 12 07-18-2005 12:07 PM


All times are GMT -5. The time now is 11:51 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved