MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > High-Performance Blades

High-Performance Blades Sharing ideas for getting the most out of our steel.

Reply
 
Thread Tools Display Modes
  #1  
Old 01-12-2002, 10:51 AM
bandaidman1
Guest
 
Posts: n/a
Most secure handle material


What is the best handle material you have found for a knife that will be used in a wet enviroment? ie fishing. Both grip security and comfort should be considered.

I love the look and feel of linen micarta and G-10 but they tend to be slick when wet unless they are "roughed up". The canvas micarta as on a busse knife is secure but is ugly and not particlularly pleasant to hold.

Recently picked up some carbon fibre handled knives but have not really tested them.

Cord wrapping can be quite secure but I do not find it a very good material for a utility blade (martial blade would be another issue).

Had a nice little stag Bird and trout once. It was really "nubbly" and felt great and was secure even wet. However after a few seasons it did not wear as well as I had hoped.

Any other thoughts?


Reply With Quote
  #2  
Old 01-12-2002, 11:15 AM
JHossom
Guest
 
Posts: n/a

My personal favorite is Canvas Micarta. It is very grippy, and stays that way when wet. Linen Micarta gets smooth pretty quickly with handling.

On that subject though, it's my firm belief that a knife should not depend on tactile feel for grip security. I think the handle should be sufficiently ergonomic to provide a secure grip even if it's dipped in oil. That of course is just this knifemaker's opinion.

BTW, I do think cord wrapped handles like on Striders is very grippy, and is easily replaced to restore it if it gets damaged. There's really no reason that handle can't be done well on any knife style besides tacticals; it just isn't.
Reply With Quote
  #3  
Old 01-13-2002, 12:07 AM
bandaidman1
Guest
 
Posts: n/a

Great points Jerry

Do you "rough up" your canvas micarta or does it grip well even in a sanded state?

I concur with your post regarding ergonomics. Not a lot of makers or manufacturers seem to emphasize that enough. I have a highly polished linen micarta blade that I can hang onto well secondary to its design (by your bud Tom Mayo). Had another blade (by a different maker) that always made me nervous to use. Needless to say I gave it away....
Reply With Quote
  #4  
Old 01-13-2002, 12:28 AM
ERIC ELSON
Guest
 
Posts: n/a

My favourites are G-10 and Carbon fiber.
I like them both because they are stable in most environments. Also I like the Grippy texture G-10 gets when you beadblast it.
I do agree that texture should not be the relied on for proper grip though.

regards

Eric

Reply With Quote
  #5  
Old 01-13-2002, 01:09 AM
JHossom
Guest
 
Posts: n/a

I sand Canvas Micarta to about 400 grit, and leave it there. When it gets wet, the water seems to get into the fabric, causing it to swell a little. So if anything it is even grippier when wet.

Is "grippier" a word?
Reply With Quote
  #6  
Old 01-13-2002, 08:19 PM
Rob Simonich
Guest
 
Posts: n/a

I started doing a grip texture back in the mid 80's that I called "Gunner Grip" I was making knives for FBI teams here in Montana and they wanted a grip that was not too harsh but grippy. This particular knife has Grn/Blk G-10 with the Gunner Grip texture. It works very well!


Reply With Quote
  #7  
Old 01-13-2002, 09:23 PM
JHossom
Guest
 
Posts: n/a

Nice knife Rob! That grip looks like a LOT of work. Should be a great feel though.
Reply With Quote
  #8  
Old 01-13-2002, 10:11 PM
Rob Simonich
Guest
 
Posts: n/a

Takes me 20 minutes to do a knife Jerry!
Reply With Quote
  #9  
Old 01-14-2002, 09:55 AM
Don Halter
Guest
 
Posts: n/a

What exactly is G10? Does this have fiberglass or carbon fibers in it? More specifically, when working it, do you get covered with little fibers from anything? I keep seeing it pop up as handles and it really looks nice.

Don Halter
Reply With Quote
  #10  
Old 01-14-2002, 10:04 AM
JHossom
Guest
 
Posts: n/a

It's fiberglass. Probably not as bad as what you're thinking for the prickly's, but certainly bad to breathe. Then again, most anything besides air isn't good for you.
Reply With Quote
  #11  
Old 01-14-2002, 07:16 PM
jeffj
Guest
 
Posts: n/a

Rob,

What do you use to get that effect?

Jeff
Reply With Quote
  #12  
Old 01-15-2002, 12:28 AM
WinDancer
Guest
 
Posts: n/a

Agressively Bead Blasted Canvas Micarta.

Dave
Reply With Quote
  #13  
Old 01-15-2002, 08:09 AM
C L Wilkins
Guest
 
Posts: n/a
Most secure handle material


Jeff,
I bet he uses golf ball skins then dyes them black!
Lets see, 287 dimbles per golf ball, I figure about three and a half golf balls ought to do it!

Yeah, I know, I'm a lot of help...

Craig
Reply With Quote
  #14  
Old 01-15-2002, 08:37 AM
jeffj
Guest
 
Posts: n/a

Thanks Craig!

Okay...next question: Where do you buy G10 golf balls?

Jeff
Reply With Quote
  #15  
Old 01-15-2002, 06:11 PM
Rob Simonich
Guest
 
Posts: n/a

Nope, not blasted Micarta, that is a G-10 handle. It takes a real sharp knife to skin thos camo golf balls, and they are so hard to find! I zing it in with a 3/16ths ball in a Dremel tool, not near as hard as it looks.
Reply With Quote
Reply

Tags
blade, knife, knives


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

(View-All Members who have read this thread : 2
MikeT, Steve Barbour
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 01:20 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved