MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > Fine Embellishment

Fine Embellishment Everything from hand engraving and scrimshaw to filework and carving. The fine art end of the knifemaker's craft.

Reply
 
Thread Tools Display Modes
  #1  
Old 12-20-2005, 03:34 PM
Big-Un Big-Un is offline
Member
 
Join Date: Mar 2005
Location: Eden, NC
Posts: 22
How to secure work in vise

I saw on here somewhere that someone used hot glue to hold the piece to be engraved to the vise but can't seem to locate it. Any help on how to use hot glue and how to pry it loose when the work is complete?
Reply With Quote
  #2  
Old 12-20-2005, 04:39 PM
Ray Cover Jr Ray Cover Jr is offline
Master
 
Join Date: Apr 2004
Posts: 926
I use hot glue for most knives. It does not work as well for large gun actions but for knives and smallish objects it works great.

First mask off your knife with tape. Then glue the piece to a small block of hardwood or metal ( I use small brass blocks). It helps to warm the metal piece. Sometimes it does not stick real well if the block is too cold.

WHen you are ready to take it off. pry up an edge of the glue and pour a little rubbing alcohol between the glue and metal. Then GENTLY lift/pry it all apart.

Make sure you dry any alcohol off metal parts and add a touch of oil if its carbon steel. The alcohol can rust the metal if you just leave it on there.

Ray


__________________
Ray Cover
Fine Art Engraving School
rcoverengraving.com

ray@rcoverengraving.com
Reply With Quote
  #3  
Old 12-20-2005, 05:12 PM
Big-Un Big-Un is offline
Member
 
Join Date: Mar 2005
Location: Eden, NC
Posts: 22
Thanks

Thank you for the information. I couldn't remember what was used to remove it.

Bill
Reply With Quote
  #4  
Old 12-20-2005, 08:28 PM
ron p. nott ron p. nott is offline
Living Legend
 
Join Date: Jun 2002
Location: sunnerdale pa
Posts: 1,540
i use super glue . i found that this stuff works very well, i even use it when i am milling cavities for inter frame knives that i make . i glue it to a piece of steel and when i am finished i just smack the back of the steel with a hammer and it pops right off then i soap it in acetone for a few minutes .. to clean off any glue that still is on it . i also glue small parts to steel that i have to engrave or gold inlay .. Ron


__________________
ron p. nott
Reply With Quote
  #5  
Old 12-25-2005, 07:30 PM
Jinkers Jinkers is offline
Registered
 
Join Date: Nov 2005
Posts: 5
Another trick to the hot glue - for short term use, is to spray the piece you need to hold with wd40 - squirt out the hot glue and stick the piece in the glue - kinda letting it sink in just a bit - when you are done, the piece is lubricated so you get a corner started and it slides away from the glue. Not suggested for those week long projects tho
Reply With Quote
  #6  
Old 12-26-2005, 02:13 PM
Don Cowles's Avatar
Don Cowles Don Cowles is offline
Founding Member / Moderator
 
Join Date: Jun 2002
Location: Royal Oak, Michigan
Posts: 2,192
Send a message via AIM to Don Cowles
GRS is selling some cool plastic stuff that you can soften in the microwave, and form to odd-shaped work pieces.


__________________


Don Cowles Custom Knives

Reply With Quote
  #7  
Old 12-26-2005, 02:54 PM
BrianPowley BrianPowley is offline
Enthusiast
 
Join Date: Jun 2005
Location: Bloomingdale, Ohio
Posts: 90
The product from GRS is called Thermo-Loc.
It works very well and is re-usable over and over again.
When microwaved or heated with a heat gun, it is very pliable and molds to any shape.
When it cools down it is extremely hard and non-marring.

I use it in 2 pieces for a custom vise jaw that fits each side of the parts.
I put a piece of a Wal-Mart shopping bag on the part before setting it in the Thermo-Loc. The Thermo-Loc will not stick to the Wal-Mart plastic bag. After the Thermo-Loc sets up, I can open up the vise jaws and remove the part without having to heat it up. (Kinda like a release agent.)
Brian
Reply With Quote
  #8  
Old 12-26-2005, 05:12 PM
Ray Cover Jr Ray Cover Jr is offline
Master
 
Join Date: Apr 2004
Posts: 926
Brilliant idea Brian!

I am going to have to try that.

Ray


__________________
Ray Cover
Fine Art Engraving School
rcoverengraving.com

ray@rcoverengraving.com
Reply With Quote
Reply

Tags
blade, knife, knives


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 11:22 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved