MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > High-Performance Blades

High-Performance Blades Sharing ideas for getting the most out of our steel.

Reply
 
Thread Tools Display Modes
  #1  
Old 09-29-2006, 09:11 PM
EdStreet EdStreet is offline
Guru
 
Join Date: Sep 2005
Location: Columbus, GA
Posts: 1,050
silver casting

So i've been looking all over for some 3mm (8 gauge) sterling sheets. so far none to be found.

Question is this, what do I need to cast my own?

Ed


__________________
Gold is for the mistress - silver for the maid
Copper for the craftsman cunning in his trade.
"Good!" said the Baron, sitting in his hall
But steel - cold steel is master of them all.
Rudyard Kipling (1865 - 1936)
Reply With Quote
  #2  
Old 09-29-2006, 10:37 PM
McAhron's Avatar
McAhron McAhron is offline
Living Legend
 
Join Date: Sep 2003
Location: Under the Redwoods in Beautiful La Honda CA
Posts: 1,642
I looked through all my Jewelers supply catalogs and the thickest I found was 2.6mm At ReoGrande.If I run across some I'll let you know.What are you making that requires 1/8th inch sterling sheet?


__________________
N'T McAhron Sqwaukin Vulture Verrinder
"to create is to make art"
TREMBLING EARTH KNIFE WORKS
Reply With Quote
  #3  
Old 09-29-2006, 11:35 PM
EdStreet EdStreet is offline
Guru
 
Join Date: Sep 2005
Location: Columbus, GA
Posts: 1,050
well here's th deal. I have a damascus dagger I want to use sterling for bolsters. I figured 3mm was somewhat on the small side.

Anyways, here's my schematics.


note the front and rear bolster, the front I have yet to draw in but that's max limits, the rear will be filled in.

And here's the damascus it's goign to fit on


and the front bolster location


The goal is to put sterling on both sides of the ivory and use sterling pins and ebony spacers. I also thought about using 2 layers of sterling. I have looked everywhere and the thickness I need/want seems unobtainable so I figured the best way to go is cast my own stuff or find someone to cast the mold I make.

Ed


__________________
Gold is for the mistress - silver for the maid
Copper for the craftsman cunning in his trade.
"Good!" said the Baron, sitting in his hall
But steel - cold steel is master of them all.
Rudyard Kipling (1865 - 1936)
Reply With Quote
  #4  
Old 09-30-2006, 01:37 AM
McAhron's Avatar
McAhron McAhron is offline
Living Legend
 
Join Date: Sep 2003
Location: Under the Redwoods in Beautiful La Honda CA
Posts: 1,642
If you cant find what you need then you could high temp solder several pieces together.I agree,even 3mm would be thin for this design.Your drwing doesnt have demensions on the width of the bolsters(outer edge to edge)RioGrande has .625x.188/15.8x4.8mm rectangles,order#100-589


__________________
N'T McAhron Sqwaukin Vulture Verrinder
"to create is to make art"
TREMBLING EARTH KNIFE WORKS
Reply With Quote
  #5  
Old 09-30-2006, 01:44 AM
McAhron's Avatar
McAhron McAhron is offline
Living Legend
 
Join Date: Sep 2003
Location: Under the Redwoods in Beautiful La Honda CA
Posts: 1,642
Here you go.1/4 thick 1x1inch,also available in longer lengths at Surepure Chemetals, http://www.surepure.com/products.php...7&meas2_ID=1ls,


__________________
N'T McAhron Sqwaukin Vulture Verrinder
"to create is to make art"
TREMBLING EARTH KNIFE WORKS
Reply With Quote
  #6  
Old 09-30-2006, 09:33 AM
B.Finnigan's Avatar
B.Finnigan B.Finnigan is offline
Living Legend
 
Join Date: Jun 2005
Location: Near Rainier WA
Posts: 1,986
If you are feeling adventurous you can cold hammer silver down to the thickness you need. Use a MAPP or propylene torch to anneal the silver and it will soften up enough to cold hammer without cracking. MAPP gas cylinders can found at most hardware stores for $8-$9 and they fit on a regular propane torch head. Heat the metal to a dark cherry red color and then quench it in water. It does not need to be quenched unless you want to imediately start hammering. You can air cool it while you go take a break and it will also soften that way.

After you get close to the thickness then you can file and then sand it to the exact thickness. I just cold hammered a copper belt buckle and it was fun because there is no forge or heat to deal with besides doing a couple anneals. The hammering will work harden non-ferrous metals so you have to anneal when you start to notice the metal not moving as fast under the hammer.

In the amount of time you probably spent searching the net you could have made the bolsters. That is one of the "yard sticks" I use when I decide to start with raw materials vs. trying to find something that appears to not exist.
Reply With Quote
  #7  
Old 09-30-2006, 10:10 AM
Shakudo's Avatar
Shakudo Shakudo is offline
Skilled
 
Join Date: Nov 2003
Location: Minnesota
Posts: 672
3mm is around the thickness you get from a 2 piece ingot mold. check with the local jewelers in your area and see if any will pour an ingot for you. do you have your own silver already? if not you are looking at around $60 worth of silver plus a shop fee.
Reply With Quote
  #8  
Old 09-30-2006, 11:19 AM
EdStreet EdStreet is offline
Guru
 
Join Date: Sep 2005
Location: Columbus, GA
Posts: 1,050
interesting. I called several shops local and everyone told me they cant do ir or order it.

I didn't think about hammering it. Also thanks for the link but that's plain silver, not sterling. I am going to end up using just plain silver I suspect. going to the coin shop today and get some ingots thats similar thickness/size I need.

I currently do not have my own silver, I did find a place that sells the rods I need, also have sterling tubing in 1/4inch and 1/2 inch which would be good for lanyard holes.

I did get the name/address of someone local who im told does casting and going to call her on monday.

Ed


__________________
Gold is for the mistress - silver for the maid
Copper for the craftsman cunning in his trade.
"Good!" said the Baron, sitting in his hall
But steel - cold steel is master of them all.
Rudyard Kipling (1865 - 1936)
Reply With Quote
  #9  
Old 09-30-2006, 12:56 PM
rhrocker's Avatar
rhrocker rhrocker is offline
Hall of Famer
 
Join Date: Nov 2002
Location: Uvalde, Texas
Posts: 3,117
Interesting Ed. Please keep us posted on how your project is going. That's a really nice dagger by the way, your work? I need to pore some silver for a project eventually, so I'll be following this very closely. I guess I better start by finding out the difference between silver, .999 fine, and sterling. I've not messed with the stuff much.


__________________
Robert Hensarling
Uvalde, Texas




Hensarling Custom Knives

Reply With Quote
  #10  
Old 09-30-2006, 01:04 PM
EdStreet EdStreet is offline
Guru
 
Join Date: Sep 2005
Location: Columbus, GA
Posts: 1,050
This damascus is not my work. The guy I bought it from does alot of damascus and quite good at it to.

mostly the difference in sterling and .995/.999 is sterling is 7.5% copper and 92.5% silver.
Sterling is alot harder than regular silver and holds up where regular silver is soft and easy to mark. This is why 'nickel/silver' a.k.a. 'german silver' is used alot, looks similar but not quite the same and a big difference.

I also have several others from this guy and see the damascus forum for images

Ed


__________________
Gold is for the mistress - silver for the maid
Copper for the craftsman cunning in his trade.
"Good!" said the Baron, sitting in his hall
But steel - cold steel is master of them all.
Rudyard Kipling (1865 - 1936)
Reply With Quote
  #11  
Old 09-30-2006, 02:04 PM
B.Finnigan's Avatar
B.Finnigan B.Finnigan is offline
Living Legend
 
Join Date: Jun 2005
Location: Near Rainier WA
Posts: 1,986
I have bought alot of silver from CC Silver. He has a good selection and you can buy very small amounts.

http://www.ccsilver.com/silver/silver.html

Last edited by B.Finnigan; 10-02-2006 at 02:22 PM.
Reply With Quote
  #12  
Old 10-01-2006, 12:14 PM
J.Arthur Loose's Avatar
J.Arthur Loose J.Arthur Loose is offline
Moderator
 
Join Date: Jun 2002
Location: Vermont
Posts: 1,403
Send a message via AIM to J.Arthur Loose Send a message via Yahoo to J.Arthur Loose
I have an ingot mold from Rio that is 4mm thick and about 1.5" x 3".

Heat the ingot to around 500 F in the oven and pour molten silver into it. Use a large tip from oxy / acetylene or better, oxy propane / mapp. Melt in a melting crucible also available from Rio. For thicker pieces I would do some sand casting.

You could also carve the pieces in wax and lost wax cast them. This is the easiest way, and you can get the carving wax from Rio. There are many casters who will do all the work for you. Carving the pieces in wax or even wood and sand casting them would be a very easy alternative as well, especially as the back of the bolster is flat.

I recommend Tim McCreight's book Practical Casting.


__________________






jloose.com

Reply With Quote
  #13  
Old 10-01-2006, 01:42 PM
EdStreet EdStreet is offline
Guru
 
Join Date: Sep 2005
Location: Columbus, GA
Posts: 1,050
awsome! just what I was looking for. Should not be to hard or expensive at all. I just ordered that book to. If I was to setup something small it should no be that complex either.

Ed


__________________
Gold is for the mistress - silver for the maid
Copper for the craftsman cunning in his trade.
"Good!" said the Baron, sitting in his hall
But steel - cold steel is master of them all.
Rudyard Kipling (1865 - 1936)
Reply With Quote
  #14  
Old 10-02-2006, 11:16 AM
Doug Lester Doug Lester is offline
Hall of Famer
 
Join Date: Sep 2006
Location: Decatur, IL
Posts: 2,612
Talking Ingot molds

Go to www.contenti.com, they have an adjustable ingot mold, 50x45x3.5mm, listed on sale for just under $18. The 3.5mm is a fixed demention.

Doug Lester
Reply With Quote
  #15  
Old 04-03-2007, 09:51 PM
EdStreet EdStreet is offline
Guru
 
Join Date: Sep 2005
Location: Columbus, GA
Posts: 1,050
I am going with the casting method instead. Several reasons for this, biggest one is cost, another is shape. I am playing around with sand casting and going to use some air hardening modeling clay to make the impression then sand cast it and pour silver. Should have minimal loss this way.

Ed


__________________
Gold is for the mistress - silver for the maid
Copper for the craftsman cunning in his trade.
"Good!" said the Baron, sitting in his hall
But steel - cold steel is master of them all.
Rudyard Kipling (1865 - 1936)
Reply With Quote
Reply

Tags
blade, forge, knife


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 11:36 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved