MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > The Sheath/Holster Makers Forum

The Sheath/Holster Makers Forum This is the place to discuss all forms of sheath and holster making.

Reply
 
Thread Tools Display Modes
  #1  
Old 03-10-2002, 06:44 PM
foxcreek
Guest
 
Posts: n/a
splicing thread


What's the best way of adding additional waxed linen when stitching and you find you dont have enough to finish? I haven't found a knot that will hold in the waxed linen. there has to be a standard way of dealing with this. any ideas?
Reply With Quote
  #2  
Old 03-10-2002, 07:24 PM
wbkco
Guest
 
Posts: n/a
splice


Try a drop of super glue on the knot and pull it into one of the holes
TJ
Reply With Quote
  #3  
Old 03-11-2002, 06:07 AM
Don Cowles
Guest
 
Posts: n/a
Re: splice


Cut off the thread flush with the leather, and start again with new thread 3 or 4 holes back (so 3 or 4 holes will be double-stitched). Make sure you have enough the second time.
Reply With Quote
  #4  
Old 03-11-2002, 07:20 AM
cgillock
Guest
 
Posts: n/a
splicing


Don is exactly correct on the splicing method.
Reply With Quote
  #5  
Old 03-11-2002, 01:38 PM
ansoknives
Guest
 
Posts: n/a
Re: splicing


Ya I was about to suggest the same as Don when I read his post....it is so tiresom to find out you need just a few more inches of tread isn?t...I have started to calculate just how much I need by checking the thickness of the sheath and then say the lenght of the stitchen * 3-5..ussually gives enough...if I have less than one foot left on each side I am happy...
Reply With Quote
  #6  
Old 03-11-2002, 07:57 PM
foxcreek
Guest
 
Posts: n/a
Re: splicing


Thanks all, I usually have some left over at the end but this sheath was extra thick and I was way off. I did over lap, doubled up through three holes, and it worked fine, made a little variation in the appearance but enough to really matter. I was surprised how secure it felt, that over lapping through must sort of wedge the thread in the holes.
Reply With Quote
  #7  
Old 03-11-2002, 09:15 PM
helmar4578
Guest
 
Posts: n/a
Re: splicing


In order to do a real neat job of double stitching so the double stitches do not look thicker or of more bulk,Try this----When you are nearing the end of the thread take your stitching gouge and run one more pass on your stitch line for the last three stitches. This will slightly lower the stitches (Bury them deeper) so that when you sew through and over these stitches it will not show where the splice has been made. If both sides are to show, gouge the other side also.
Reply With Quote
  #8  
Old 04-25-2019, 04:41 PM
Sandy1105 Sandy1105 is offline
 
Join Date: Aug 2017
Location: 1105 Stephens Rd. Blairsville, GA 30512
Posts: 5
BTTTT----over seventeen years since tnis was posted---where does the time go> Sandy Morrissey
Reply With Quote
  #9  
Old 04-25-2019, 10:40 PM
TexasJack's Avatar
TexasJack TexasJack is offline
Super Moderator
 
Join Date: Apr 2004
Location: Southeast Texas
Posts: 2,822
Do any threads actually disappear without a moderator deleting them?

I suspect this is a question that crops up a lot. To my surprise, I knew the answer because I learned it from the book, "The Art of Hand Sewing Leather" by Al Stohlman. My copy (from Tandy) doesn't have a date in it, but I suspect the original goes back to the 1950's, judging from the pictures in it.

Don Cowles had the right answer. I've got a beautiful knife he made that I bought a LONG time ago when we were raising money for someone.


__________________
God bless Texas! Now let's secede!!
Reply With Quote
  #10  
Old 04-26-2019, 05:16 AM
Crex's Avatar
Crex Crex is offline
Moderator
 
Join Date: Sep 2002
Location: Acworth, GA and/or Hanging Dog, NC
Posts: 3,479
I had it easier TJ.....I learned it from Dad.


__________________
Carl Rechsteiner, Bladesmith
Georgia Custom Knifemakers Guild, Charter Member
Knifemakers Guild, voting member
Registered Master Artist - GA Council for the Arts
C Rex Custom Knives

Blade Show Table 5-J
Reply With Quote
Reply

Tags
a, art, back, book, hand, knife, leather, made, question


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

(View-All Members who have read this thread : 14
argel55, Art Swyhart, damon, DThrash, Ed Tipton, flintbone, hubb, jimmontg, M&J, pcpc201, Sandy1105, sheathmaker, TexasJack
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 05:07 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved