MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena Are you new to knife making? Here is all the help you will need.

Reply
 
Thread Tools Display Modes
  #1  
Old 06-01-2023, 07:01 AM
designed2fail designed2fail is offline
Registered
 
Join Date: May 2023
Posts: 1
Question about using buffalo horn

Hello first off thank you for adding me.

I am planning on using buffalo horn for a ferrule for a knife I am about to make and have never actually used it. Now will the sides with ever be as polished as the face? I test cut a sliver off to see how well it can be machined and that left a pretty reasonable face to start with, as shown in the pictures.

I read slow and steady wins the race with horn as heat will warp it. I have no qualms with hand sanding as I am going to be doing a Kijiro Urushi lacquer finish on the wood part of the handle and saya(sheath)

Now should I leave the back a bit rough or smoother the better when epoxying it to the wood components? If possible I am going to hollow it out with a down cut spiral router bit so I can make a cap for the ferrule and opening for the sheath.

also if this is the wrong section I apologize in advance. Any and all info will be very much appreciated. I thank you for your time

https://imgur.com/5ZcsMxi
https://imgur.com/Rp1JRjS
https://imgur.com/AE2crkh
Reply With Quote
  #2  
Old 06-01-2023, 08:27 AM
Ray Rogers's Avatar
Ray Rogers Ray Rogers is offline
Founding Member / Moderator
 
Join Date: Jun 2002
Location: Wauconda, WA
Posts: 9,844
Slow and steady AND fresh, sharp belts if you use your belt grinder. If you smell burning hair your belt is too fast or you're using too much pressure.

Buffalo horn seems to polish just fine on all sides and face but leaving it a little rough where epoxy will be applied seems a good idea . . .


__________________

Your question may already have been answered - try the Search button first!






Reply With Quote
  #3  
Old 06-01-2023, 02:12 PM
M&J's Avatar
M&J M&J is offline
Master
 
Join Date: Dec 2004
Location: So. Cal
Posts: 927
Welcome!

As Ray mentions. Slow is preferred as horn is soft so going slower gives you time to work it. When I epoxy surfaces up I tend to leave them at a 100 grit finish. Buffalo horn polishes nicely and a light touch on the buffer is sufficient as it is fairly soft.

With a dark horn or similar dark materials adding in a black colorant to approximate the handle color helps fill any unintentional voids. This results in a near matching color to appear seamless.


__________________
Mike
Reply With Quote
  #4  
Old 06-01-2023, 11:30 PM
TexasJack's Avatar
TexasJack TexasJack is offline
Super Moderator
 
Join Date: Apr 2004
Location: Southeast Texas
Posts: 2,922
Be sure to open a window or otherwise have lots of fresh air. Buffalo horn smells like 10,000 buffaloes just took a dump in the room. It even smells when you hand sand it.


__________________
God bless Texas! Now let's secede!!
Reply With Quote
  #5  
Old 06-03-2023, 05:26 AM
Crex's Avatar
Crex Crex is offline
Moderator
 
Join Date: Sep 2002
Location: Acworth, GA and/or Hanging Dog, NC
Posts: 3,592
Heat and humidity are it's mortal enemies and side pressure is their friend. Make sure there is no tension or pressure against the grain or it will eventually split or crack. Stuff moves constantly since it is just compressed hair so joints rarely stay smooth and clean over time.
Don't get me wrong I like it and use it quite a bit, but mostly for spacers these days. Good luck with it.


__________________
Carl Rechsteiner, Bladesmith
Georgia Custom Knifemakers Guild, Charter Member
Knifemakers Guild, voting member
Registered Master Artist - GA Council for the Arts
C Rex Custom Knives

Blade Show Table 6-H
Reply With Quote
Reply

Tags
a, art, back, belt grinder, belts, buffalo horn, ca, epoxy, finish, grinder, hand, handle, heat, horn, knife, make, polish, question, sand, sanding, sharp, sheath, show, wood


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Buffalo horn zappo The S.R. "Steve" Johnson Forum 4 03-18-2014 08:10 AM
Need buffalo horn advice. Shankmaker The Newbies Arena 8 05-31-2009 11:55 PM
Oh great...I got some buffalo horn. Shankmaker The Newbies Arena 15 04-20-2009 09:31 AM
buffalo horn!!!! EdStreet The Display Case 5 08-19-2006 09:21 PM
buffalo horn Omega Knife Making Discussions 12 06-19-2005 05:25 PM


All times are GMT -5. The time now is 06:48 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved