Custom Knives | Other Knives | General Items
New Posts | New PhotosAll Photos

Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > The S.R. "Steve" Johnson Forum

The S.R. "Steve" Johnson Forum Specialized knife making tips, technique and training for "ultra precision" design work enthusiasts.

Thread Tools Display Modes
Old 07-20-2016, 09:11 AM
s mcfall s mcfall is offline
Join Date: Aug 2002
Location: freeville n.y.
Posts: 32
what i didnt know about Loveless knives

i am friends on facebook with John Denton, and he posted a picture of a rare soldered guard on a Loveless knife...said that he used to solder them until 1992 when the solder changed and discolored his tangs, so he then when to a dry i always though they were soldered to keep moisture:water, blood ect. from getting under there so i am guessing he made them fit this the norm these days? does anyone else fry fit guards or do most still solder?
Reply With Quote
Old 07-20-2016, 09:12 PM
Doug Lester Doug Lester is offline
Hall of Famer
Join Date: Sep 2006
Location: Decatur, IL
Posts: 2,501
I don't know about the norm these days but I do know that makers do still soldier their guards. They will also use epoxy like JB Weld. However, a dry fit has been used even longer without any detriment to the knife or sword. There are even some old swords with fullered tangs that have not rusted through as some will guarantee will happen if you let moisture get under the guard.


If you're not making mistakes then you're not trying hard enough
Reply With Quote
Old 07-29-2016, 04:57 PM
argel55 argel55 is offline
Steel Addict
Join Date: Apr 2009
Location: Chandler, Oklahoma
Posts: 204
Or bolstered ones where you use a little super glue to seal the edges. I used to have an old soldering iron that was slotted to be used soldering. It was a lot better technique than using a propane torch to heat.
Reply With Quote
Old 07-30-2016, 12:55 AM
Steve's Avatar
Steve Steve is offline
Join Date: Jun 2002
Location: Manti, Utah USA
Posts: 1,229
It's true, Bob quit soldering, but many, many makers still solder. It seals the area between the guard and the tang and give a nice looking fillet around the front of the guard. I still use the same type of solder that Bob used when I was with him, in fact he had the Eutectic Rep. come to the shop when we started using 154-Cm, as it was difficult to solder. With their flux, it was a lot easier. Soldering SS is a difficult task, even with this solder and flux, as one must not overheat and there isn't a large window between being not hot enough and too hot. I do not sue solder at all with bolsters, as there is a great big space there to get flux trapped underneath and that will cause problems over time. Pop Knife supply has some great, less expensive solder that flows a little better than what we used to use. I'm hearing of a better flux, also. There are as many opinions about soldering and not soldering as there are knifemakers out there.

NRA Endowment Member
Knifemakers' Guild Member since 1971
"May you live all the days of your life." - Jonathan Swift
Reply With Quote

154-cm, bee, bolsters, epoxy, glue, guard, guards, heat, hot, iron, john, knife, knife supply, knives, loveless, made, makers, rare, shop, supply, tang, weld

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Never seen a Loveless like this! Andrew Garrett Historical Inspiration 1 11-29-2014 01:15 PM
Loveless Knives Website LovelessKnives Web Sites : Announcements 0 05-22-2014 07:40 AM
Didnt know what I had, till last night velociraptor The Newbies Arena 3 05-20-2013 09:55 AM
Questions About The Loveless City and StiffHorn Knives GHNorfleet The S.R. "Steve" Johnson Forum 6 11-21-2008 01:21 PM
Loveless Knives JediOkie Knife Collecting 3 11-07-2006 08:13 PM

All times are GMT -5. The time now is 01:08 AM.

Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved