|
|
The Folding Knife (& Switchblade) Forum The materials, techniques and the designing of folding knives. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
First two folders
Here are my first 2 folders. I'd appreciate anyone's honest opinion and feedback. |
#2
|
|||
|
|||
Your pictures did not show up. I tried copying your URL to them and can't find them that way either. Please check your message for errors and edit any problems. Sure would like to see these folders. |
#3
|
|||
|
|||
they come up fine in this end. Those are very purdy knives! Could we have some datails on materials used and size? I really like the looks of those pivots. |
#4
|
|||
|
|||
First Knives
Roland, Your doing some good work!!!!!!!!!! Keep it up. Dwayne |
#5
|
|||
|
|||
pictures
Bob, I looked at the forum this mornig and saw where Jens Anso ( Anso Knives) said they came in for him. Have you tried to get them again?. Roland |
#6
|
|||
|
|||
Re: pictures
Jens, here are the specs on the knives. Starting with the top first. Steel: A.T.S. 34 ------ H.T. by BOS Blade length: 2 1/4 " Overall length 5 3/8" Spacer, liners, bolsters, 6al4v Bolsters beveled, anodized Blue Liners & spacer jeweled Scales: M.O.P., scale screws checkered 50 l.p.i. Pivot screws: I machined those myself, and hand checkered them 40 l.p.i. Thumb stud: I machined and inset with green coral All screws are 24 ct. gold plated. Fileworked completely around 2 nd knife: Dimensions basically the same. Steel: A.T.S. 34----H.T. by BOS Spacer, liners, bolsters 6al4v Bolsters gold anodized. and beveled Scales: Ivory Thumb stud: 6al4v, anodized purple, and scalloped All screws are 24 ct. gold plated. Pivot screws : I machined those myself. Fileworked throughout |
#7
|
|||
|
|||
Re: pictures
Bob, Please let me know if the pictures came in for you Roland |
#8
|
|||
|
|||
Re: pictures
Roland, those folders look really nice, well done. Regards from Australia. |
#9
|
|||
|
|||
Re: pictures
Neil, Thank you for looking and for the kind words. I have been following up on you tutorials and hope that someday I will be making knives even a little close to that quality. You can be assured I will be asking a lot of questions. roland |
#10
|
|||
|
|||
Re: pictures
For some reason, I still cannot see them. I copy the image location and paste it into the browser and it goes but the picture does not show up. Sounds like some nice knives. |
#11
|
|||
|
|||
Re: pictures
Bob, maybe I can send them to you via e- mail attachment if you want me to. roland |
#12
|
|||
|
|||
Re: pictures
I would like to see them so please e-mail them. I also would like to figure out why they don't show up here. If others can see them your URL must be correct but for some reason I can't see them. It is like the picture is not in the location the URL points to but if others can see them, that is not the case. Confusing to me. |
#13
|
|||
|
|||
Re: pictures
Got the pictures on e-mail. Great looking folders. You do good work. As far as the pictures go, I am confused. I could not even open them as an attachment in the e-mail. I had to save them to my hard drive and then open them with another program. Pretty wierd. |
#14
|
|||
|
|||
Re: pictures
Bob, glad you got them, and thanks for looking. Hey glad to see you are a moderator on tool time with gene. I,m going to be asking lots of questions for sure. Thanks, roland |
#15
|
|||
|
|||
Re: pictures
Cute little folders there. My first few did not look that good. Bob and I will be at TOOL TIME, if you need us. Keep up the good work. |
Tags |
blade, knife, knives |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
(View-All) Members who have read this thread : 3 | |
BrownBear, coldtracker, totis |
|
|