MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > The Sheath/Holster Makers Forum

The Sheath/Holster Makers Forum This is the place to discuss all forms of sheath and holster making.

Reply
 
Thread Tools Display Modes
  #1  
Old 08-03-2018, 07:44 PM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 301
Master or Journeyman set for rivet dies?

I have a few Kydex sheaths for some upcoming pieces so I'm getting set up to do these. Is there a significant result quality between the Master and Journeyman Series offered by Knife Kits?


__________________
Mike
Reply With Quote
  #2  
Old 08-10-2018, 03:32 PM
KNAdmin's Avatar
KNAdmin KNAdmin is offline
Administrator
 
Join Date: Jun 2002
Posts: 2,111
You can get a perfect result with the Journeyman setup. The difference is in the depth of the throat clearance of the Master press...and in the ability to control the flaring pressure better. With the JS set, you're using a hammer to lightly apply force for the roll. It works like a charm, but I recommend the MS setup if you're considering doing it a lot over time.


__________________
Alex Whetsell

[======]~~~~~~~>

Atlantavirtual.com
Atlanta NOC
Reply With Quote
  #3  
Old 08-11-2018, 09:44 PM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 301
Thanks Alex! Was planning on mounting them into an arbor press if adaptable. I have a few types of knives that are Kydex type sheath candidates, those are very limited/low sub 8 production numbers.


__________________
Mike
Reply With Quote
  #4  
Old 08-13-2018, 02:58 PM
KNAdmin's Avatar
KNAdmin KNAdmin is offline
Administrator
 
Join Date: Jun 2002
Posts: 2,111
They'll work in most 3-5 ton arbors. Drill a 5/8 hole and add a set screw to hold the top die. That's all you need. They will last a lifetime.


__________________
Alex Whetsell

[======]~~~~~~~>

Atlantavirtual.com
Atlanta NOC
Reply With Quote
  #5  
Old 08-13-2018, 09:47 PM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 301
Cool! Thanks Alex!


__________________
Mike
Reply With Quote
  #6  
Old 08-14-2018, 03:53 PM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 301
Thanks for the PM Alex. The PM didn't allow a reply so wanted to post message received and


__________________
Mike
Reply With Quote
  #7  
Old 08-18-2018, 12:09 AM
KNAdmin's Avatar
KNAdmin KNAdmin is offline
Administrator
 
Join Date: Jun 2002
Posts: 2,111
No reply allowed? I'll check into that. You should be able to reply to any PM around here. Hmmmm...

Let me know if you need any help.


__________________
Alex Whetsell

[======]~~~~~~~>

Atlantavirtual.com
Atlanta NOC
Reply With Quote
  #8  
Old 09-18-2018, 12:11 AM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 301
A pic of the first one. Was intended as an experiment to test the oven but it went well so this one worked out. The back part of the toaster oven is hotter so there was 1/2" of the Kydex was a bit shiny. Other than that the forming was smooth.

Some flaring of the opening to allow easier insertion and shaping where the blade locks in for the retention firmness.
Attached Images
File Type: jpg mf-knife-kydex-September 17, 2018-3969.jpg (72.5 KB, 3 views)


__________________
Mike
Reply With Quote
Reply

Tags
a, apply, arbor, back, blade, ca, dies, drill, hammer, help., hot, kits, knife, knife kits, knives, kydex, post, press, retention, screw, set screw, sheath, sheaths


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Journeyman Smith Testing changes. Julie Coffey Ed Caffrey's Workshop 15 09-12-2012 09:45 PM
Changes to Journeyman Smith and Master Smith Testing Locations Ed Caffrey Ed Caffrey's Workshop 10 09-08-2010 07:58 AM
ABS Journeyman knives Guy Thomas Ed Caffrey's Workshop 9 07-06-2004 07:17 PM
Rivet dies question PS_Bond Knife Kits Forum 7 08-15-2003 10:53 AM
ABS Journeyman Test Knife LHKnives The Display Case 10 07-08-2002 08:33 PM


All times are GMT -5. The time now is 08:43 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved