MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > The Outpost

The Outpost This forum is dedicated to all who share a love for, and a desire to make good knives, and have fun doing it. We represent a diverse group of smiths and knifemakers who bring numerous methods to their craft.

Reply
 
Thread Tools Display Modes
  #1  
Old 08-21-2003, 08:04 AM
Gouge's Avatar
Gouge Gouge is offline
Skilled
 
Join Date: Jun 2002
Location: Butt's in Virginia, Heart's in Georgia
Posts: 408
Fun reading 1904 blacksmith

Found this while doing so research

Modern blacksmith 1904
Reply With Quote
  #2  
Old 08-21-2003, 08:22 AM
MongoForge's Avatar
MongoForge MongoForge is offline
Master
 
Join Date: Jun 2002
Location: Ohio
Posts: 961
Anybody ever try this?

AKE of nitric acid 4 ozs.; muriatic acid, ? oz. Mix togetner. Now cover the place you wish to write on with beeswax, the beeswax to be warm when applied. When it is cold, write your name with a sharp instrument. Be sure to write so that the steel is discernible in the name. Now apply the mixture with a feather, well filling each letter. Let the mixture remain about five minutes or more, according to the depth desired; then wash off the acid; water will stop the process of the same. When the wax is removed, the inscription is plain.


__________________
"NT Truckin Aardvark Montgomery"
www.geocities.com/montyforge/index.html
Reply With Quote
  #3  
Old 08-21-2003, 09:03 AM
Sweany's Avatar
Sweany Sweany is offline
Hall of Famer
 
Join Date: Jun 2002
Location: Sand Springs OK
Posts: 2,303
Don't use something that will scratch the steel. Like an exacto knife. Use a sharpened brass rod or a leather modeling tool.

The scratches in the steel get etched to and look like crap.

I used this method with ferric chloride.
Nitric is kinda nasty from what I remember.

David Boye has a section is his book devoted to etching.

I etch customer intials on blades with those vinyl stick on letters from the office supply store.

I surround the letters with a cut out from a piece of clear plastic laminate. Apply all to a throughly cleaned , and warmed blade. I use ammonia, and a light bulb.

Make a little "pond"around the template with modelling clay and fill with ferric chloride. 5 to ten minutes depending on depth of etch required.



l


__________________
NT Barkin Turtle Tribe ~~~Life is what it is~~~
Reply With Quote
  #4  
Old 08-21-2003, 09:14 AM
Gouge's Avatar
Gouge Gouge is offline
Skilled
 
Join Date: Jun 2002
Location: Butt's in Virginia, Heart's in Georgia
Posts: 408
TO MAKE STEEL AND IRON AS WHITE AS SILVER
Take 1 pound of ashes from white ash bark, dissolve in soft water. Heat your iron red, and cool in this solution, and the iron will turn white as silver.
Reply With Quote
  #5  
Old 08-23-2003, 07:48 AM
Crex's Avatar
Crex Crex is offline
Moderator
 
Join Date: Sep 2002
Location: Acworth, GA and/or Hanging Dog, NC
Posts: 3,583
Tried it yet Chicken Toes? Old techniques are pretty neat and sometimes so simple.

Mongo - been using the technique for over 30 years. It's the only way I've found to mark my miniatures cleanly. Yeah nitric is pretty nasty stuff. You must use great care. I usually use a fine tipped ball point pen to mark through the wax. Just lightly heat the metal to be etched with a heatgun or hairdryer and melt a thin layer of clarified beeswax on it. Thinner the better. I always
"killed" the etch with ammonia bleach just to be sure. Work a little cold blue in and rewarm the metal and remove the wax with a rag. Quite easy.

Crex


__________________
Carl Rechsteiner, Bladesmith
Georgia Custom Knifemakers Guild, Charter Member
Knifemakers Guild, voting member
Registered Master Artist - GA Council for the Arts
C Rex Custom Knives

Blade Show Table 6-H
Reply With Quote
  #6  
Old 08-23-2003, 07:55 PM
Dana Acker Dana Acker is offline
Moderator
 
Join Date: Jun 2002
Location: Mt. Airy, North Carolina, USA
Posts: 1,888
Great article--those old guys knew a lot. I'm glad someone had the sense to preserve the knowledge. Thanks for posting that.


__________________
http://www.ackerforge.com
Reply With Quote
Reply

Tags
forging, knife


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 03:41 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved