|
|
|
|
|
|
||
|
|
|
|
||
|
|||||||
| The Supply Center What's Hot ... and where the deals are! Supplies are our specialty ... |
 |
|
|
Thread Tools | Display Modes |
|
#1
09-17-2002, 10:44 PM
|
|||
|
|||
|
Nickle Silver
Does anybody know where to get nickle silver in 3/8 x 1 inch thick by 12 inch or 6 inches long. Have tryed a lot of suppliers with no luck.
Dan www.theknifemaker.com 
|
|
#2
09-17-2002, 11:00 PM
|
||||
|
||||
|
K&G stocks it. Part #HM16.
http://www.knifeandgun.com/ __________________ Mike
|
|
#3
09-17-2002, 11:29 PM
|
|||
|
|||
|
nickle silver
Mike,
Thanks. There web site has been shut down for repairs. I will call them in the morning. Dan www.theknifemaker.com
|
|
#4
09-20-2002, 07:45 PM
|
|||
|
|||
|
out
Mike,
They are out also. Cant find this stuff anywhere. Can anyone help? Dan ww.theknifemaker.com
|
|
#6
09-21-2002, 09:35 AM
|
|||
|
|||
|
Dan have you tryed Sheffield Knife Supply thay have had it when no one else has had it. Gib
__________________ 
|
|
#7
09-21-2002, 09:36 AM
|
|||
|
|||
|
Mike,
Thanks for the offer, but I need 1 inch wide for a ferrel that fits a great pc of elk horn. I dont know why but all the suppliers are stocking 3/4 inch wide material and no longer stock 1 inch. I also cant find any round nickle silver that is 1 inch. Guess I will have to switch to stainless. My lathe has a rough time with it. It amazes me, the politeness of people on this forum and the help that people like you offer. If I would have said yes you would have taken the time out of you schedule to help a fellow knifemaker. This is a great place to be. Thanks. Dan www.theknifemaker.com
|
|
#8
09-21-2002, 11:53 AM
|
||||
|
||||
|
You might try Sheffield, and if they don't have barstock, maybe they have a 6"x6"x3/8" sheet, or something similar.
If you go with stainless steel, get 416, it's not bad to work with. At least compared to the 300 series. http://www.sheffieldsupply.com/ __________________ Mike
|
|
#9
09-21-2002, 03:42 PM
|
||||
|
||||
|
I have a piece of nickel silver that is 1" x 3/8" x 3" if that would help. Let me know: don@cowlesknives.com.
|
|
#10
09-22-2002, 09:04 AM
|
|||
|
|||
|
found it
Don,
Thanks for the offer but I found it in sheets at Sheffield. Again, it amazes me the help that you guys offer. Now if I can just get the knife together without any "murphy's". Dan www.theknifemaker.com
|
|
#11
09-23-2002, 09:15 AM
|
||||
|
||||
|
You can make a knife without any "Murphys"????
 I'm lucky if I can get away with only a half dozen.... I guess I better keep up with my practice. Mike __________________ No Chance, No Dance
|
|
| Tags |
| knife |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
