MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena New to Knife Making? Here's all the help you need ...

Reply
 
Thread Tools Display Modes
  #1  
Old 04-03-2017, 10:55 AM
nflknives nflknives is offline
Enthusiast
 
Join Date: Nov 2016
Location: Tallahassee
Posts: 34
brass butt cap

if i drill a piece of brass and solder a piece of 3/16 brass rod into in and epoxy that into the antler will that work for capping the end of the antler handle and then sand it down to the form of the antler? My son wanted one like this but i have never done a butt plate.
Reply With Quote
  #2  
Old 04-03-2017, 11:43 AM
dtec1 dtec1 is offline
Guru
 
Join Date: Aug 2015
Location: putnam county NY ....about 45 mins north of new york city
Posts: 1,133
I have never done it that way. The best way to do it is make it a hidden tang and get a piece of threaded rod (can be found at any hardware store) Cut a slot in the end of the hidden tang big enough to "seat" the threaded rod....braze that rod to the tang. Then you drill a hole into the brass end cap and tap it with the same size thread as the rod. Then you just cut the rod to size (measure twice cut once...ii have made that mistake and it sucks!...put the rod through the antler epoxy it in there with a lil bit of the rod sticking out the end and simply screw the brass end cap on....I don't know the facts behind it but for me brazing is a whole lot stronger than anything I have soldered and its very simple to do all ya need is a good brazing rod and a torch
Reply With Quote
  #3  
Old 04-03-2017, 07:25 PM
jimmontg jimmontg is offline
Skilled
 
Join Date: Jan 2016
Location: Mountains of Western NC.
Posts: 744
How thick is the butt cap? If it's 3/16 or thicker I drill a partial hole about 3/4 through the brass and tap it 1/4-20 with a bottom tap and then solder the screw in. I then drill a hole in the antler and tap it, then fill with epoxy and screw the butt plate on. You can also take a matching brass screw and go all the way through the butt plate as well if it's only 1/8" thick and no solder needed just use superglue or loctite on the threads. The strongest method if you can't solder a long screw to the tang. I have tapped wood and antlers and it works well with epoxy.

I always use brass screws in case I have to drill all the way through like the 3/16 is too thin to hold a screw unless it goes all the way through or is soldered. If you have 10-24 or 10-32 brass screws that fine too. Use a 7/32 drill bit for tapping 1/4-20 and 5/32 for 10-24, unless you have set of number drills, but those are close enough.

Last edited by jimmontg; 04-03-2017 at 07:36 PM.
Reply With Quote
Reply

Tags
antler, brass, drill, epoxy, fixed blade, handle, hardware, hidden, hidden tang, made, make, ore, rod, sand, screw, simple, solder, store, tang, tap, wood


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Jim Behring 4-1/2" Sticker Knife With Brass Butt Perryknifeworks Knives For Sale - Custom 0 10-01-2014 11:31 PM
Found an old looking all brass folding knife with a brass blade, information? rx7rotary13b Knife Network Community 2 02-10-2012 10:17 PM
Need help on butt plate Joe Mason Fine Embellishment 5 05-17-2003 09:57 PM
Engraving a butt cap gravertom Fine Embellishment 2 02-21-2003 09:18 PM
Butt-cap for stag dancbr929 Fit & Finish 4 03-15-2002 02:59 PM


All times are GMT -5. The time now is 12:45 PM.




KNIFENETWORK.COM
Copyright © 2000
CKK Industries, Inc. All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved