MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena Are you new to knife making? Here is all the help you will need.

Reply
 
Thread Tools Display Modes
  #1  
Old 03-27-2018, 09:51 PM
KevBooth KevBooth is offline
Enthusiast
 
Join Date: Apr 2017
Location: Northern Utah
Posts: 79
Bolsters

Iíve been practicing attaching bolsters to scrap of blade steel, and Iím getting pretty good and consistent results. Iím to the point where I feel like I can attach them to a blade and end up with a presentable product.
My question is this. What if anything is everyone using to attach the bolsters to the scale besides the peening of the pins? Iíve seen epoxy used, solder, nothing... Iím just curious what those with experience have used with the best results.
Thank you
Reply With Quote
  #2  
Old 03-28-2018, 08:59 AM
Ray Rogers's Avatar
Ray Rogers Ray Rogers is offline
Founding Member / Moderator
 
Join Date: Jun 2002
Location: Wauconda, WA
Posts: 9,772
You couldn't pay me to put bolsters on a knife but that's just me.

I assume you meant to ask about attaching the bolsters to the tang and not the scales. Yes, they are usually pinned. Most people put some epoxy under them because there needs to be something under there to keep moisture from collecting there and causing trouble. Solder is the super professional way to do that but there's hardly anyone these days that has really mastered the proper way to solder a bolster....


__________________

Your question may already have been answered - try the Search button first!






Reply With Quote
  #3  
Old 03-28-2018, 11:50 AM
KevBooth KevBooth is offline
Enthusiast
 
Join Date: Apr 2017
Location: Northern Utah
Posts: 79
I just like that way that a metal bolster finishes off the knife. To my eye it just adds another level of craftsmanship, and finish to the overall knife. But I do harbor some concerns about moisture and other things causing problems under the surface, hence the questions.

Yes I actually did mean to say, "attached to the tang", my fingers can't type as fast as my brain can think. My concern with using epoxy is the cosmetic affect of a visual line between the bolster and tang, that would appear as improper fit. I take all precautions to insure flatness on both pieces, and I would hate to ruin that.

Thanks
Reply With Quote
  #4  
Old 03-28-2018, 04:58 PM
Bob Hatfield Bob Hatfield is offline
Steel Addict
 
Join Date: Apr 2004
Location: Northern CA.
Posts: 107
You can use Q-tips and alcohol, or acetone to clean up any epoxy that may squeeze out on to the blade ricasso.


__________________
RELH
Reply With Quote
  #5  
Old 03-28-2018, 05:28 PM
jimmontg jimmontg is offline
Guru
 
Join Date: Jan 2016
Location: Now live in Las Cruces NM.
Posts: 1,156
Kevin use a clear epoxy and clamp the bolstered down hard when you peen it and there will not be a line of glue visible. If you use JB Weld it's hard to not have a visible line because it's blackish.
Reply With Quote
  #6  
Old 03-28-2018, 06:59 PM
damon damon is offline
Skilled
 
Join Date: Jul 2013
Location: NE Tennessee
Posts: 408
keep the surfaces flat, and clean. The pin holes as well. Keep fittings and pins tight. peen thoroughly. when done properly the pins will not be visible, and there will be no place for moisture to reach between bolster and tang.
Reply With Quote
  #7  
Old 03-29-2018, 08:25 AM
dtec1 dtec1 is offline
Guru
 
Join Date: Aug 2015
Location: putnam county NY ....about 45 mins north of new york city
Posts: 1,443
i tend to agree bolsters just look great AS long as the rest of the knife is good too....as ray says no sense in putting lipstick on a pig....but what i do is go the peening route so you need to make sure you have the same material like 416 stainles for bolsters AND pins....360 brass for bolsters and pins if you just use any brass for the bolsters and any brass for the pins you run the risk of having visable pins once ground flush....however i use 2 differnt epoxys acra glass or gflex... They are both clear so if done right you want have the line like you would with jbweld so what i do is get the bolsters ready and put a little epoxy on the inside put the pins through there holes....what i like to do is stop and wait a minute not long enough for the epoxy to fully set just long enough that it starts to stiffen then i peen the pins in at that point the excess epoxy will come out and by that time it should be thickening up where its a lil bit easier to clean off the excess get as much of it off as possible then some people like to take a brass rod and put a point on it and lightly use it to pop off any epoxy left after it hardens...personally yes brass is softer than steel so it shouldnt scratch the blade but what i use is a wooden rod (not sure what kind of wood it is but i do know its a hardwood not soft) or what you could do is get a rod of micarta g10 or carbon fiber and use that just use the point to "chisle" off the excess in front of the bolsters...just remember when you put them on the longer you sit there and take it off with a qtip and acetone the more you take off now the less you will need to pop off after its hard....i have a vise to hold the knife right between my tv and laptop so as it dries i dont get bored while wiping it off every couple mins as it dries (i get bored quick lol) ..OR you could make a folder and just put them on with screws :-)
Reply With Quote
Reply

Tags
a, bee, blade, bolster, bolsters, ca, clean, collecting, epoxy, flat, glue, knife, metal, pins, question, scale, scales, solder, steel, surface, tang, tips, weld


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
bolsters gharper@awesome The Newbies Arena 1 09-15-2006 07:55 PM
Bolsters on or off? Russ Sutton Fine Embellishment 2 10-27-2005 12:55 PM
GX6 Bolsters ErikD Knife Kits Forum 9 01-13-2004 10:14 PM
? for Don re bolsters SVanderkolff The Newbies Arena 1 12-08-2002 04:22 PM
Bolsters RickNJ Fit & Finish 3 06-28-2002 09:56 PM


All times are GMT -5. The time now is 12:06 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved