MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena Are you new to knife making? Here is all the help you will need.

Reply
 
Thread Tools Display Modes
  #1  
Old 05-14-2024, 04:00 PM
M&J's Avatar
M&J M&J is offline
Master
 
Join Date: Dec 2004
Location: So. Cal
Posts: 927
Shop wear -vent

A buddy relayed he was contacted by the buyer who had bought a knife from a dealer and was asked if the knife could be freshened up a bit. When the knife arrived he commented that it looked like it had seen significant use rather than just "shop wear".

I've encountered "shop wear" as well where knives on consignment get played with so they get scratched up. This becomes more of an issue with titanium that has been anodized yet similar with 416 bolsters.

It is frustrating how some customers handle knives yet this happens at shows where they are not very careful in their handling. Have seen customers flick the knife open to have it fly out of their hands onto the floor as well. (That's another gripe discussion.)


__________________
Mike
Reply With Quote
  #2  
Old 05-20-2024, 07:45 AM
Crex's Avatar
Crex Crex is offline
Moderator
 
Join Date: Sep 2002
Location: Acworth, GA and/or Hanging Dog, NC
Posts: 3,592
Hear you big time, my nemesis is the sheath splitter. Folks that have no clue how to sheath a knife.

Had a guy at the Blade many moons ago split the side out of a $200 sheath with the $600 knife (it was custom fitted for). He didn't think I saw it so he set it back on the table and turned to walk away. Before I could say something, his wife grabbed him by the ear and marched him to the middle of my table to face me. She instructed him to pull out his wallet and dig deep. Told her I could redo the sheath to make the purchase "clean", but she said "NO, he needs the lesson"! Could have kissed her right there and probably should have.


__________________
Carl Rechsteiner, Bladesmith
Georgia Custom Knifemakers Guild, Charter Member
Knifemakers Guild, voting member
Registered Master Artist - GA Council for the Arts
C Rex Custom Knives

Blade Show Table 6-H
Reply With Quote
  #3  
Old 05-21-2024, 08:09 PM
M&J's Avatar
M&J M&J is offline
Master
 
Join Date: Dec 2004
Location: So. Cal
Posts: 927
Great story!


__________________
Mike
Reply With Quote
  #4  
Old 05-22-2024, 07:13 AM
Crex's Avatar
Crex Crex is offline
Moderator
 
Join Date: Sep 2002
Location: Acworth, GA and/or Hanging Dog, NC
Posts: 3,592
There are also the ones with toxic finger sweat, they seem to have to touch everything but buy nothing. Then there are the "St. Bernards " that spray when they talk. Probably the worst part of shows like the Blade is the re-cleaning when I get home.


__________________
Carl Rechsteiner, Bladesmith
Georgia Custom Knifemakers Guild, Charter Member
Knifemakers Guild, voting member
Registered Master Artist - GA Council for the Arts
C Rex Custom Knives

Blade Show Table 6-H
Reply With Quote
  #5  
Old 05-22-2024, 12:02 PM
TexasJack's Avatar
TexasJack TexasJack is offline
Super Moderator
 
Join Date: Apr 2004
Location: Southeast Texas
Posts: 2,922
Great stories!

I made a knife for a friend and gave it to him while we were all out celebrating his birthday. First time he stuck the knife back in the sheath, he held it at an angle and cut right through the sheath, nearly cutting himself in the process. How do you idiot proof something that simple?

I overheard a guy talking about buying a nice knife but he felt like it needed to be sharper. A friend of his offered t sharpen it for him. When he got it back, the edge was crooked and the blade was scratched from one end to the other. Turned out that the friend had a WalMart knife sharpener with the rods that are stuck in a wood block. For whatever reason, the friend felt like the faster he moved the knife, the faster it would sharpen. The first lesson would be that if someone says they know how to do something, make them show you before handing over your valuable knife to them. The second lesson is that sharpening a knife should be a basic requirement to get your "man card". (Other requirements should be, changing a tire, building a fire, bandaging a wound with electricians tape, using a plunger on a plugged toilet, painting a room, understanding the basic rules of baseball, football, and basketball - with the exception of the "balk", which nobody understands.)


__________________
God bless Texas! Now let's secede!!
Reply With Quote
  #6  
Old 05-24-2024, 04:12 PM
M&J's Avatar
M&J M&J is offline
Master
 
Join Date: Dec 2004
Location: So. Cal
Posts: 927
That is where Kydex comes in. I've been wanting to try a lined Kydex sheath since it is a bit quieter. The thing is that it is heavier and the time to cost ratio makes those marginal builds in my mind.

Have seen some of those hacked sharpening jobs. One begins to think they took an angle grinder like sharpening a lawn mower blade routine. Have seen some pretty messed up re-finish jobs too.


__________________
Mike
Reply With Quote
Reply

Tags
a, back, bee, blade, bolsters, buy, clean, cleaning, custom, edge, handle, home, how to, knife, knives, make, nemesis, sharpening, sheath, shop, spray, titanium


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
need to vent newbie13 The Newbies Arena 4 04-20-2014 12:56 PM
new shop - vent question SVanderkolff Knife Making Discussions 2 06-09-2009 07:16 PM
Aarrgh!!!! Need To Vent! Craig B. Knife Making Discussions 3 08-09-2004 09:49 PM
Need to vent! Mace Knife Making Discussions 1 08-03-2004 09:42 PM
Let me vent! Terrill Hoffman Knife Photography Discussion 4 07-24-2002 07:59 AM


All times are GMT -5. The time now is 04:14 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved