|
|
Register | All Photos | FAQ | Members List | Calendar | ShopStream (Radio/TV) | Search | Today's Posts | Mark Forums Read |
Heat Treating and Metallurgy Discussion of heat treatment and metallurgy in knife making. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
heat treating W1
Can anyone refer me to a decent W1 heat treating formula?
Or, does anyone have one they prefer and would care to share? Something reliable, I hope! Thanks! __________________ Blade Show Table 8-Q What do you do when you see your ex in pain, limping and bleeding? Relax. Take a deep breath. Reload and then shoot again. http://www.andersenforge.com/ |
#2
|
|||
|
|||
I would search this forum, bladeforums, and Don Fogg's forum for posts on W1 by Randall Graham and Nick Wheeler. They have both written alot of really great stuff.
JOhn __________________ John Frankl |
#3
|
||||
|
||||
Karl, W1 is one of my favorite steels. It is basicly a better grade of 1095. I heat to 1450 hold for a few min.s then quench in a fast oil, then two one hour tempers at 400 deg.s. I am forging blades from W1 drill rod and it's been a very, very clean steel with predictable results.
I forgot to mention that I finish forging with lower heats and also normalize once just above critical then agian at critical and last at just below critical. I also like to soak for one hour at 1300 deg.s in my kiln. After reading alot of Kevin Cashen's posts, I am rethinking the way I heat treat a have started working with the info he has be sharing. Thanks Kevin Last edited by Don Hanson; 07-31-2006 at 11:12 PM. |
#4
|
|||
|
|||
quick question
Don, just a quick question. It may be a little off topic, but what team does you cat play for?
Doug Lester |
#5
|
|||
|
|||
Quote:
__________________ "I want to play with your poodle" Lightnin' Hopkins, long ago Steve Hayden steve4663@gmail.com Aztec, NM |
#6
|
||||
|
||||
Quote:
Last edited by Don Hanson; 08-01-2006 at 07:39 PM. |
#7
|
||||
|
||||
Thanks, Don. I'll see how that works for me.
__________________ Blade Show Table 8-Q What do you do when you see your ex in pain, limping and bleeding? Relax. Take a deep breath. Reload and then shoot again. http://www.andersenforge.com/ |
#8
|
||||
|
||||
Don, do you bring the blade up to temp WITH the oven, or do you put it in after the oven has reached soak? Is this accomplishing a sperodizing procedure? I do something similar with my 5160, yet a much longer soaking segment, and it does a great job. I got the "recipe" from Tim Zowada, who helps design Even Heat's knife ovens and salt pots. Really makes the steel easy to work with, and brings everything equal making for a good hardening! I swear, after doing my sperodizing anneal, my steel gets harder on quench.
__________________ Blade Show Table 8-Q What do you do when you see your ex in pain, limping and bleeding? Relax. Take a deep breath. Reload and then shoot again. http://www.andersenforge.com/ |
#9
|
||||
|
||||
Karl, I bring the oven up to 1300 with the blade in, then hold for an hour. I started doing this years ago with my billets of mosaic damascus bolster stock that needed to go to the bandsaw. I like the way the steel cut and drilled so I started doing it with my blades. I didn't know what it was called until reading some of Cashen's writings but I did know it was good. I think Al Dippold told me about this. I also do one normalize before I quench.
|
Tags |
blade, ca, forging, heat, heat treating, heat treatment, knife, post |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|