The S.R. "Steve" Johnson Forum Specialized knife making tips, technique and training for "ultra precision" design work enthusiasts. |
11-16-2016, 05:09 PM
|
Guru
|
|
Join Date: Jan 2016
Location: Now live in Las Cruces NM.
Posts: 1,345
|
|
MSC had them? I missed them then. Graingers may have them too, but their website is hard to navigate. Like you have to write Jobber length carbide tipped drill bits or screw machine drill bits, real picky navigation. Sometimes I just call them. It's like looking for zippers under Z and finding them under I instead for Interlocking slide fasteners. I've seen screws under fasteners too, that was the Army.lol
|
11-16-2016, 06:52 PM
|
Enthusiast
|
|
Join Date: Aug 2011
Location: Linden, CA
Posts: 56
|
|
Yep I found them at MSC. It was not cheap. I think the pilot and the counterbore together was $130. I only bought the one for quarter-inch Corby bolts since that's the only size I use. I'm sure it will be worth it though, I bought a new step drill for the last pearl handle I worked with and I wouldn't use that same step drill on another piece of pearl. That step drill was $24.
|
11-18-2016, 05:07 PM
|
Enthusiast
|
|
Join Date: Aug 2011
Location: Linden, CA
Posts: 56
|
|
I have "Big Book" that I forgot I even had. It is much easier for me to thumb through paper unless like you say you know the exact term or part number. If I remember correctly, I just went online and requested a catalog and one was sent to me. It might have cost $5. I don't remember. The great thing about MSC, they ship in one day. I ordered on Monday and got the counterbore on Wednesday.
|
04-03-2018, 02:04 AM
|
|
Moderator
|
|
Join Date: Jun 2002
Location: Manti, Utah USA
Posts: 1,244
|
|
Thank you, MSC is one very handy book and, as youmention, give great service!
__________________
http://www.srjknives.com
NRA Endowment Member
Knifemakers' Guild Member since 1971
"May you live all the days of your life." - Jonathan Swift
|
03-18-2022, 07:01 PM
|
Registered
|
|
Join Date: Mar 2022
Location: Calhoun, LA
Posts: 1
|
|
[QUOTE=Steve;479902]Some ideas. Use them all, or whatever you like. I'm sure there are others out there.
Use brand new drills and counterbores, or at least "very sharp" ones. Carbide are best. Bathe it in paint thinner with a solder brush. Back up the "off side" when drilling to help stop "popping out"
Thanks again STEVE, working with turquois / mop scale first time, and using as a spacer on my partial tang.
|
03-20-2022, 03:20 PM
|
|
Master
|
|
Join Date: Dec 2004
Location: So. Cal
Posts: 927
|
|
My suggestion would be to consider diamond cutting tools as an option. Water works well as a cutting agent and adding a drop of dish soap also helps. I've drilled scales submerged as well so no dust which makes clean up nice since I just pour that into the yard. This works well for stone which is why I use it for MOP.
Typical bits can fracture or cause the MOP to chip-flake out due to the flute design where diamond abrades rather than "cuts" through, leaving a clean hole. Just have to have a more gentle feed rate as the diamond can do the work.
Turquoise is pretty soft and easy to work, similar to marble where no specialty tools are necessary. Diamond makes it easier if available. AO abrasives are sufficient though I would suggest silicon carbide to grind them wet and reduce dust. Same with MOP.
__________________
Mike
|
Tags
|
advice, back, bee, blade, brand, drill, flat, grind, handle, heat, horn, hot, knife, make, material, materials, mother of pearl, paint, pearl, saw blade, sharp, small, solder, tips, woods |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
All times are GMT -5. The time now is 06:15 PM.
|