MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena Are you new to knife making? Here is all the help you will need.

Reply
 
Thread Tools Display Modes
  #1  
Old 11-23-2018, 01:58 PM
Randi Strunk Randi Strunk is offline
 
Join Date: Nov 2018
Posts: 3
Brand new

Hi everyone I'm brand new to the hobby of knife making was wandering if anyone could tell me the bare necessities that I would need to make a full functional knife
Reply With Quote
  #2  
Old 11-23-2018, 02:34 PM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 346
Welcome! What type of knives do you feel you'll be making, fixed blade or folding? Any tools or machinery presently on hand? Many options available: The least $ investment starting from near zero would be files, sandpaper and a drill.


__________________
Mike
Reply With Quote
  #3  
Old 11-23-2018, 03:28 PM
Randi Strunk Randi Strunk is offline
 
Join Date: Nov 2018
Posts: 3
I was figuring fixed blade as I like the look of the finished product and as of current I have a bench grinder and an older drill press
Reply With Quote
  #4  
Old 11-23-2018, 05:16 PM
Doug Lester Doug Lester is offline
Hall of Famer
 
Join Date: Sep 2006
Location: Decatur, IL
Posts: 2,523
Just about any reliable drill press will do but one specifically set up to drill metal would be best. One where you can get the speed really low. Bench grinders are not all that good though some have learned to use them. Then, as mentioned there would be a good selection of files from a large bastard file to seconds and smooth files. Of course this assumes that you are planning to make knives by the stock removal method. If you want to forge your blades then you will have to add a forge and anvil of some type.

Actually you may need a forge if you are doing stock removal to heat treat the blades. To keep the cost down it would be best to build your own. An alternative would be to send your blades out to a heat treater but most of them only so air quenching steels.

If you do heat treat your own blades you will also need an oven to temper the blades in. This can be the kitchen oven if you are using simple steels, with the Chief Cooks permission. Or you can use a toaster oven.

For shaping the handles I would recommend cabinet makers rasps.

Doug


__________________
If you're not making mistakes then you're not trying hard enough
Reply With Quote
  #5  
Old 11-24-2018, 09:35 AM
Ray Rogers's Avatar
Ray Rogers Ray Rogers is offline
Founding Member / Moderator
 
Join Date: Jun 2002
Location: Wauconda, WA
Posts: 9,758
The best way to know what tools you need is to try to build a knife in the first place. The easiest way to do that is to do it in steps. The easiest steps are found with kit knives. Go to knifekits.com and look at the blades they have and pick one. Buy some handle materials from the same site and assemble the knife. This is a fairly cheap method of learning the processes of making a knife and you're guaranteed to end up with a usable knife which is always a good morale builder. Once you have confidence and the tools to attach and shape a handle you can think about making your own blades. It is a stone cold be-atch to stumble through making that first blade - which will be very challenging - only to discover that the "easy" part you were ignoring (the handle) turns that first blade into a clunky mess.

And Doug is right about the bench grinder, they are basically useless for knife making. You'll need a belt sander eventually. For now, do a couple of kit blades. Then make a couple using files and sand paper. All the hand tools and processes you acquire while doing these things will be needed on every knife you make in the future even after you have all the power tools you can imagine. Power tools make the necessary steps go faster but they don't give you the skills you need. Knife making is an art and a craft that takes years to learn properly, be patient and learn to walk before you try to run ...


__________________

Your question may already have been answered - try the Search button first!






Reply With Quote
  #6  
Old 11-24-2018, 02:55 PM
Randi Strunk Randi Strunk is offline
 
Join Date: Nov 2018
Posts: 3
Thanks for the replies it's good to know people are willing to help
Reply With Quote
  #7  
Old 11-24-2018, 05:05 PM
cnccutter's Avatar
cnccutter cnccutter is offline
Steel Addict
 
Join Date: Mar 2011
Location: Dorena, Oregon
Posts: 179
Randi, you’ll be amazed at how helping the knife community is. You might fill out your profile a bit so we know where you hail from. There might be a maker pretty close to you that could be willing to have you over for a few hours to help you get going. Two hours with some one would be worth a 100 hours of struggling.

Erik


__________________
Erik Land
Dorena, Oregon
Reply With Quote
  #8  
Old 11-24-2018, 06:53 PM
epicfail48 epicfail48 is offline
Enthusiast
 
Join Date: Aug 2017
Location: Springfield Mo
Posts: 95
All you really need to make a knife is a somewhat abrasive brick and a bar of steel, everything after that just makes the process a little easier. We really do need more information for a better recommendation of tools, what you need varies a lot based on what youre planning to make and how. If you plan on doing kit knives you can get by with just getting a hand drill and a couple files.

Stock removal knives, youll need something more along the lines of a belt sander/grinder, files, drill press, possibly an angle grinder or two, and this is all assuming you send your blades out for heat treatment. Forging, all of the above, plus a forge, anvil, hammers, etc.

If youre planning on doing pocket knives, folders and the like, it muddies the water even more. Depending on what style folder youre making and how you plan on getting the hardware, you can add anything to that list from a disc grinder to a milling machine. Theres a lot of unknowns going on there
Reply With Quote
Reply

Tags
anvil, bench grinder, blade, brand, drill, files, fixed, fixed blade, folding, forge, grinder, hand, heat treat, helping, hobby, hunting knife, knife, knife making, knives, make, making, press, profile, tools


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Brand new Frag-Out! The Newbies Arena 4 01-19-2013 10:48 AM
Brand X Raymond Richard The Outpost 2 02-13-2011 08:05 AM
Brand X Raymond Richard The Display Case 1 02-10-2011 06:31 PM
Brand X Raymond Richard The Outpost 6 11-13-2008 04:22 PM
New brand of ale Gene Chapman The Watering Hole 0 02-27-2007 06:57 PM


All times are GMT -5. The time now is 05:38 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved