MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena Are you new to knife making? Here is all the help you will need.

Reply
 
Thread Tools Display Modes
  #1  
Old 11-20-2018, 03:38 PM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 346
The challenges and screw-up's.

By now I like to feel that I have a grasp of my own making process. I have batch of 3 folders underway that are about 85% complete. I've got the locks cut, detent installed and what remains is basically the final finish and fit-up. Prior to disassembly they all worked. Came back to them last week and the blades did not match the body. I'm thinking, ok, I may have swapped blades so tested each blade among the 3 bodies. 2 fit but the third one is a "WTH" moment. It doesn't match any of the bodies and looks like I ground the stop about 1/8" off.

The other part is that even though the bodies are still supposed to be oversized by 1/32" I've already over shaped around the bolsters that I have more blade exposed for the blade arc. Read that as I now need to make new liners and bolsters. Luckily the handle scales are still within range but this batch is a head scratcher. Particularly bad because this is some old school damascus from Daryl Meir that I'm not about to be circular file.

moment. LOL...


__________________
Mike
Reply With Quote
  #2  
Old 11-20-2018, 10:04 PM
jimmontg jimmontg is offline
Guru
 
Join Date: Jan 2016
Location: Now live in Las Cruces NM.
Posts: 1,132
Thanks for reminding me why l don't make folders.
Reply With Quote
  #3  
Old 11-21-2018, 09:18 AM
Ray Rogers's Avatar
Ray Rogers Ray Rogers is offline
Founding Member / Moderator
 
Join Date: Jun 2002
Location: Wauconda, WA
Posts: 9,758
I, on the other hand, have made a lot of folders. Everyone is different and we all have our own ways of getting to the finished product but I learned early that trying to make a 'batch' of folders was a bad idea for me. Maybe it would be OK after you have completely mastered your process but batching while learning just means you make the same mistake a bunch of times. After 20 years I still found that my end result was better if I made them one at a time start to finish. After all, I think of myself as a knife maker and not a knife manufacturer .....


__________________

Your question may already have been answered - try the Search button first!






Reply With Quote
  #4  
Old 11-22-2018, 12:26 AM
cnccutter's Avatar
cnccutter cnccutter is offline
Steel Addict
 
Join Date: Mar 2011
Location: Dorena, Oregon
Posts: 179
Iím with Ray. I just donít like batchís. I usually work on two at a time and have separate trays for parts. I never have both folders out on the bench at the same time. I guess the main reason I even do two ata time is I hate to heat up my heat treat oven and buy dry ice for for just one. Use the KISS method as long as you can.


Erik


__________________
Erik Land
Dorena, Oregon
Reply With Quote
  #5  
Old 12-08-2018, 07:35 AM
Crex's Avatar
Crex Crex is offline
Moderator
 
Join Date: Sep 2002
Location: Acworth, GA and/or Hanging Dog, NC
Posts: 3,443
Hate when that happens. Shop gremlins are a buggar! I tried one of those piezo pest repellers to no avail.


__________________
Carl Rechsteiner, Bladesmith
Georgia Custom Knifemakers Guild, Charter Member
Knifemakers Guild, voting member
Registered Master Artist - GA Council for the Arts
C Rex Custom Knives

Blade Show Table 5-J
Reply With Quote
  #6  
Old 12-08-2018, 08:36 PM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 346
LOL, I'm my worst gremlin. Today I set up some CF scales to drill and during the process the clamp shifted and so to did the scale...there went two pieces for circular file. That same feeling of doing it to MOP has happened too. That's part of it...


__________________
Mike
Reply With Quote
  #7  
Old 12-09-2018, 05:40 PM
jimmontg jimmontg is offline
Guru
 
Join Date: Jan 2016
Location: Now live in Las Cruces NM.
Posts: 1,132
What are CF scales? I know what MOP ones are, mother of pearl, but l feel like l should know what the CF stands for.
Reply With Quote
  #8  
Old 12-09-2018, 07:39 PM
M&J's Avatar
M&J M&J is offline
Skilled
 
Join Date: Dec 2004
Location: So. Cal
Posts: 346
Carbon fiber-CF.


__________________
Mike
Reply With Quote
  #9  
Old 12-09-2018, 08:03 PM
jimmontg jimmontg is offline
Guru
 
Join Date: Jan 2016
Location: Now live in Las Cruces NM.
Posts: 1,132
Ah! Of course. lol
Reply With Quote
Reply

Tags
art, back, blades, bolsters, buy, ca, carbon, damascus, detent, drill, file, finish, hand, handle, handle scales, heat, heat treat, knife, knives, made, make, making, scales, screw, shop


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
glueing challenges SVanderkolff The Sheath/Holster Makers Forum 4 05-28-2010 10:13 PM
Hidden Challenges Bigblue17 Knife Making Discussions 2 11-28-2007 01:03 PM
Button head screw vs. Pan head screw alexkuzn The Folding Knife (& Switchblade) Forum 12 06-17-2007 07:53 AM
More size and complexity challenges Buddy Thomason Knife Photography Discussion 13 07-07-2006 02:32 PM
Challenges & opportunities for the amateur photographer at the ABS Reno Show Buddy Thomason Knife Photography Discussion 22 02-04-2005 06:49 PM


All times are GMT -5. The time now is 12:36 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved